/* $OpenBSD: if_axereg.h,v 1.18 2007/06/10 10:15:35 mbalmer Exp $ */
/*
* Copyright (c) 1997, 1998, 1999, 2000-2003
* Bill Paul <wpaul@windriver.com>. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software
* must display the following acknowledgement:
* This product includes software developed by Bill Paul.
* 4. Neither the name of the author nor the names of any co-contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
* THE POSSIBILITY OF SUCH DAMAGE.
*
* $FreeBSD: src/sys/dev/usb/if_axereg.h,v 1.2 2003/06/15 21:45:43 wpaul Exp $
*/
/*
* Definitions for the ASIX Electronics AX88172 to ethernet controller.
*/
/*
* Vendor specific commands
* ASIX conveniently doesn't document the 'set NODEID' command in their
* datasheet (thanks a lot guys).
* To make handling these commands easier, I added some extra data
* which is decided by the axe_cmd() routine. Commands are encoded
* in 16 bites, with the format: LDCC. L and D are both nibbles in
* the high byte. L represents the data length (0 to 15) and D
* represents the direction (0 for vendor read, 1 for vendor write).
* CC is the command byte, as specified in the manual.
*/
#define AXE_CMD_LEN(x) (((x) & 0xF000) >> 12)
#define AXE_CMD_DIR(x) (((x) & 0x0F00) >> 8)
#define AXE_CMD_CMD(x) ((x) & 0x00FF)
#define AXE_172_CMD_READ_RXTX_SRAM 0x2002
#define AXE_182_CMD_READ_RXTX_SRAM 0x8002
#define AXE_172_CMD_WRITE_RX_SRAM 0x0103
#define AXE_172_CMD_WRITE_TX_SRAM 0x0104
#define AXE_182_CMD_WRITE_RXTX_SRAM 0x8103
#define AXE_CMD_MII_OPMODE_SW 0x0106
#define AXE_CMD_MII_READ_REG 0x2007
#define AXE_CMD_MII_WRITE_REG 0x2108
#define AXE_CMD_MII_READ_OPMODE 0x1009
#define AXE_CMD_MII_OPMODE_HW 0x010A
#define AXE_CMD_SROM_READ 0x200B
#define AXE_CMD_SROM_WRITE 0x010C
#define AXE_CMD_SROM_WR_ENABLE 0x010D
#define AXE_CMD_SROM_WR_DISABLE 0x010E
#define AXE_CMD_RXCTL_READ 0x200F
#define AXE_CMD_RXCTL_WRITE 0x0110
#define AXE_CMD_READ_IPG012 0x3011
#define AXE_172_CMD_WRITE_IPG0 0x0112
#define AXE_172_CMD_WRITE_IPG1 0x0113
#define AXE_172_CMD_WRITE_IPG2 0x0114
#define AXE_178_CMD_WRITE_IPG012 0x0112
#define AXE_CMD_READ_MCAST 0x8015
#define AXE_CMD_WRITE_MCAST 0x8116
#define AXE_172_CMD_READ_NODEID 0x6017
#define AXE_172_CMD_WRITE_NODEID 0x6118
#define AXE_178_CMD_READ_NODEID 0x6013
#define AXE_178_CMD_WRITE_NODEID 0x6114
#define AXE_CMD_READ_PHYID 0x2019
#define AXE_172_CMD_READ_MEDIA 0x101A
#define AXE_178_CMD_READ_MEDIA 0x201A
#define AXE_CMD_WRITE_MEDIA 0x011B
#define AXE_CMD_READ_MONITOR_MODE 0x101C
#define AXE_CMD_WRITE_MONITOR_MODE 0x011D
#define AXE_CMD_READ_GPIO 0x101E
#define AXE_CMD_WRITE_GPIO 0x011F
#define AXE_CMD_SW_RESET_REG 0x0120
#define AXE_CMD_SW_PHY_STATUS 0x0021
#define AXE_CMD_SW_PHY_SELECT 0x0122
#define AXE_SW_RESET_CLEAR 0x00
#define AXE_SW_RESET_RR 0x01
#define AXE_SW_RESET_RT 0x02
#define AXE_SW_RESET_PRTE 0x04
#define AXE_SW_RESET_PRL 0x08
#define AXE_SW_RESET_BZ 0x10
#define AXE_SW_RESET_IPRL 0x20
#define AXE_SW_RESET_IPPD 0x40
/* AX88178 documentation says to always write this bit... */
#define AXE_178_RESET_MAGIC 0x40
#define AXE_178_MEDIA_GMII 0x0001
#define AXE_MEDIA_FULL_DUPLEX 0x0002
#define AXE_172_MEDIA_TX_ABORT_ALLOW 0x0004
/* AX88178 documentation says to always write 1 to reserved bit... */
#define AXE_178_MEDIA_MAGIC 0x0004
#define AXE_178_MEDIA_ENCK 0x0008
#define AXE_172_MEDIA_FLOW_CONTROL_EN 0x0010
#define AXE_178_MEDIA_RXFLOW_CONTROL_EN 0x0010
#define AXE_178_MEDIA_TXFLOW_CONTROL_EN 0x0020
#define AXE_178_MEDIA_JUMBO_EN 0x0040
#define AXE_178_MEDIA_LTPF_ONLY 0x0080
#define AXE_178_MEDIA_RX_EN 0x0100
#define AXE_178_MEDIA_100TX 0x0200
#define AXE_178_MEDIA_SBP 0x0800
#define AXE_178_MEDIA_SUPERMAC 0x1000
#define AXE_RXCMD_PROMISC 0x0001
#define AXE_RXCMD_ALLMULTI 0x0002
#define AXE_172_RXCMD_UNICAST 0x0004
#define AXE_178_RXCMD_KEEP_INVALID_CRC 0x0004
#define AXE_RXCMD_BROADCAST 0x0008
#define AXE_RXCMD_MULTICAST 0x0010
#define AXE_RXCMD_ENABLE 0x0080
#define AXE_178_RXCMD_MFB 0x0300
#define AXE_NOPHY 0xE0
#define AXE_INTPHY 0x10
#define AXE_TIMEOUT 1000
#define AXE_172_BUFSZ 1536
#define AXE_178_MIN_BUFSZ 2048
#define AXE_178_MAX_BUFSZ 16384
#define AXE_RX_LIST_CNT 1
#define AXE_TX_LIST_CNT 1
#define AXE_CTL_READ 0x01
#define AXE_CTL_WRITE 0x02
#define AXE_CONFIG_NO 1
#define AXE_IFACE_IDX 0
/*
* The interrupt endpoint is currently unused
* by the ASIX part.
*/
#define AXE_ENDPT_RX 0x0
#define AXE_ENDPT_TX 0x1
#define AXE_ENDPT_INTR 0x2
#define AXE_ENDPT_MAX 0x3
struct axe_type {
struct usb_devno axe_dev;
u_int16_t axe_flags;
#define AX178 0x0001 /* AX88178 */
#define AX772 0x0002 /* AX88772 */
};
struct axe_softc;
struct axe_chain {
struct axe_softc *axe_sc;
usbd_xfer_handle axe_xfer;
char *axe_buf;
struct mbuf *axe_mbuf;
int axe_accum;
int axe_idx;
};
struct axe_cdata {
struct axe_chain axe_tx_chain[AXE_TX_LIST_CNT];
struct axe_chain axe_rx_chain[AXE_RX_LIST_CNT];
int axe_tx_prod;
int axe_tx_cons;
int axe_tx_cnt;
int axe_rx_prod;
};
struct axe_sframe_hdr {
u_int16_t len;
u_int16_t ilen;
} __packed;
struct axe_softc {
struct device axe_dev;
#define GET_MII(sc) (&(sc)->axe_mii)
struct arpcom arpcom;
#define GET_IFP(sc) (&(sc)->arpcom.ac_if)
struct mii_data axe_mii;
usbd_device_handle axe_udev;
usbd_interface_handle axe_iface;
u_int16_t axe_vendor;
u_int16_t axe_product;
u_int16_t axe_flags;
int axe_ed[AXE_ENDPT_MAX];
usbd_pipe_handle axe_ep[AXE_ENDPT_MAX];
int axe_unit;
int axe_if_flags;
struct axe_cdata axe_cdata;
struct timeout axe_stat_ch;
int axe_refcnt;
char axe_dying;
char axe_attached;
struct usb_task axe_tick_task;
struct usb_task axe_stop_task;
struct rwlock axe_mii_lock;
int axe_link;
unsigned char axe_ipgs[3];
unsigned char axe_phyaddrs[2];
struct timeval axe_rx_notice;
u_int axe_bufsz;
};
![[BACK]](/icons/back.gif){kind=icon}
Return to if_axereg.h CVS log ![[TXT]](/icons/text.gif){kind=icon}
![[DIR]](/icons/dir.gif){kind=icon}
Up to [local] / sys / dev / usb