Annotation of sys/dev/ic/rtl80x9reg.h, Revision 1.1
1.1 ! nbrk 1: /* $OpenBSD: rtl80x9reg.h,v 1.2 2003/10/21 18:58:49 jmc Exp $ */
! 2: /* $NetBSD: rtl80x9reg.h,v 1.2 1998/10/31 00:31:43 thorpej Exp $ */
! 3:
! 4: /*-
! 5: * Copyright (c) 1998 The NetBSD Foundation, Inc.
! 6: * All rights reserved.
! 7: *
! 8: * This code is derived from software contributed to The NetBSD Foundation
! 9: * by Jason R. Thorpe of the Numerical Aerospace Simulation Facility,
! 10: * NASA Ames Research Center.
! 11: *
! 12: * Redistribution and use in source and binary forms, with or without
! 13: * modification, are permitted provided that the following conditions
! 14: * are met:
! 15: * 1. Redistributions of source code must retain the above copyright
! 16: * notice, this list of conditions and the following disclaimer.
! 17: * 2. Redistributions in binary form must reproduce the above copyright
! 18: * notice, this list of conditions and the following disclaimer in the
! 19: * documentation and/or other materials provided with the distribution.
! 20: * 3. All advertising materials mentioning features or use of this software
! 21: * must display the following acknowledgement:
! 22: * This product includes software developed by the NetBSD
! 23: * Foundation, Inc. and its contributors.
! 24: * 4. Neither the name of The NetBSD Foundation nor the names of its
! 25: * contributors may be used to endorse or promote products derived
! 26: * from this software without specific prior written permission.
! 27: *
! 28: * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
! 29: * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
! 30: * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
! 31: * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
! 32: * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
! 33: * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
! 34: * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
! 35: * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
! 36: * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
! 37: * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
! 38: * POSSIBILITY OF SUCH DAMAGE.
! 39: */
! 40:
! 41: /*
! 42: * Registers on RealTek 8019 and 8029 NE2000-compatible network interfaces.
! 43: *
! 44: * Data sheets for these chips can be found at:
! 45: *
! 46: * http://www.realtek.com.tw
! 47: */
! 48:
! 49: #ifndef _DEV_IC_RTL80x9_REG_H_
! 50: #define _DEV_IC_RTL80x9_REG_H_
! 51:
! 52: /*
! 53: * Page 0 register offsets.
! 54: */
! 55: #define NERTL_RTL0_8019ID0 0x0a /* 8019 ID Register 0 */
! 56: #define RTL0_8019ID0 'P'
! 57:
! 58: #define NERTL_RTL0_8019ID1 0x0b /* 8019 ID Register 1 */
! 59: #define RTL0_8019ID1 'p'
! 60:
! 61: /*
! 62: * Page 3 register offsets.
! 63: */
! 64: #define NERTL_RTL3_EECR 0x01 /* EEPROM Command Register */
! 65: #define RTL3_EECR_EEM1 0x80 /* EEPROM Operating Mode */
! 66: #define RTL3_EECR_EEM0 0x40
! 67: /* 0 0 Normal operation */
! 68: /* 0 1 Auto-load */
! 69: /* 1 0 9346 programming */
! 70: /* 1 1 Config register write enab */
! 71: #define RTL3_EECR_EECS 0x08 /* EEPROM Chip Select */
! 72: #define RTL3_EECR_EESK 0x04 /* EEPROM Clock */
! 73: #define RTL3_EECR_EEDI 0x02 /* EEPROM Data In */
! 74: #define RTL3_EECR_EEDO 0x01 /* EEPROM Data Out */
! 75:
! 76: #define NERTL_RTL3_BPAGE 0x02 /* BROM Page Register (8019) */
! 77:
! 78: #define NERTL_RTL3_CONFIG0 0x03 /* Configuration 0 (ro) */
! 79: #define RTL3_CONFIG0_JP 0x08 /* jumper mode (8019) */
! 80: #define RTL3_CONFIG0_BNC 0x04 /* BNC is active */
! 81:
! 82: #define NERTL_RTL3_CONFIG1 0x04 /* Configuration 1 (8019) */
! 83: #define RTL3_CONFIG1_IRQEN 0x80 /* IRQ Enable */
! 84: #define RTL3_CONFIG1_IRQS2 0x40 /* IRQ Select */
! 85: #define RTL3_CONFIG1_IRQS1 0x20
! 86: #define RTL3_CONFIG1_IRQS0 0x10
! 87: /* 0 0 0 int 0 irq 2/9 */
! 88: /* 0 0 1 int 1 irq 3 */
! 89: /* 0 1 0 int 2 irq 4 */
! 90: /* 0 1 1 int 3 irq 5 */
! 91: /* 1 0 0 int 4 irq 10 */
! 92: /* 1 0 1 int 5 irq 11 */
! 93: /* 1 1 0 int 6 irq 12 */
! 94: /* 1 1 1 int 7 irq 15 */
! 95: #define RTL_CONFIG1_IOS3 0x08 /* I/O base Select */
! 96: #define RTL_CONFIG1_IOS2 0x04
! 97: #define RTL_CONFIG1_IOS1 0x02
! 98: #define RTL_CONFIG1_IOS0 0x01
! 99: /* 0 0 0 0 0x300 */
! 100: /* 0 0 0 1 0x320 */
! 101: /* 0 0 1 0 0x340 */
! 102: /* 0 0 1 1 0x360 */
! 103: /* 0 1 0 0 0x380 */
! 104: /* 0 1 0 1 0x3a0 */
! 105: /* 0 1 1 0 0x3c0 */
! 106: /* 0 1 1 1 0x3e0 */
! 107: /* 1 0 0 0 0x200 */
! 108: /* 1 0 0 1 0x220 */
! 109: /* 1 0 1 0 0x240 */
! 110: /* 1 0 1 1 0x260 */
! 111: /* 1 1 0 0 0x280 */
! 112: /* 1 1 0 1 0x2a0 */
! 113: /* 1 1 1 0 0x2c0 */
! 114: /* 1 1 1 1 0x2e0 */
! 115:
! 116: #define NERTL_RTL3_CONFIG2 0x05 /* Configuration 2 */
! 117: #define RTL3_CONFIG2_PL1 0x80 /* Network media type */
! 118: #define RTL3_CONFIG2_PL0 0x40
! 119: /* 0 0 TP/CX auto-detect */
! 120: /* 0 1 10baseT */
! 121: /* 1 0 10base5 */
! 122: /* 1 1 10base2 */
! 123: #define RTL3_CONFIG2_8029FCE 0x20 /* Flow Control Enable */
! 124: #define RTL3_CONFIG2_8029PF 0x10 /* Pause Flag */
! 125: #define RTL3_CONFIG2_8029BS1 0x02 /* Boot Rom Size */
! 126: #define RTL3_CONFIG2_8029BS0 0x01
! 127: /* 0 0 No Boot Rom */
! 128: /* 0 1 8k */
! 129: /* 1 0 16k */
! 130: /* 1 1 32k */
! 131: #define RTL3_CONFIG2_8019BSELB 0x20 /* BROM disable */
! 132: #define RTL3_CONFIG2_8019BS4 0x10 /* BROM size/base */
! 133: #define RTL3_CONFIG2_8019BS3 0x08
! 134: #define RTL3_CONFIG2_8019BS2 0x04
! 135: #define RTL3_CONFIG2_8019BS1 0x02
! 136: #define RTL3_CONFIG2_8019BS0 0x01
! 137:
! 138: #define NERTL_RTL3_CONFIG3 0x06 /* Configuration 3 */
! 139: #define RTL3_CONFIG3_8019PNP 0x80 /* PnP Mode */
! 140: #define RTL3_CONFIG3_FUDUP 0x40 /* Full Duplex */
! 141: #define RTL3_CONFIG3_LEDS1 0x20 /* LED1/2 pin configuration */
! 142: /* 0 LED1 == LED_RX, LED2 == LED_TX */
! 143: /* 1 LED1 == LED_CRS, LED2 == MCSB */
! 144: #define RTL3_CONFIG3_LEDS0 0x10 /* LED0 pin configuration */
! 145: /* 0 LED0 pin == LED_COL */
! 146: /* 1 LED0 pin == LED_LINK */
! 147: #define RTL3_CONFIG3_SLEEP 0x04 /* Sleep mode */
! 148: #define RTL3_CONFIG3_PWRDN 0x02 /* Power Down */
! 149: #define RTL3_CONFIG3_8019ACTIVEB 0x01 /* inverse of bit 0 in PnP Act Reg */
! 150:
! 151: #define NERTL_RTL3_CSNSAV 0x08 /* CSN Save Register (8019) */
! 152:
! 153: #define NERTL_RTL3_HLTCLK 0x09 /* Halt Clock */
! 154: #define RTL3_HLTCLK_RUNNING 'R' /* clock runs in power down */
! 155: #define RTL3_HLTCLK_HALTED 'H' /* clock halted in power down */
! 156:
! 157: #define NERTL_RTL3_INTR 0x0b /* ISA bus states of INT7-0 (8019) */
! 158:
! 159: #define NERTL_RTL3_8029ID0 0x0e /* ID register 0 */
! 160:
! 161: #define NERTL_RTL3_8029ID1 0x0f /* ID register 1 */
! 162:
! 163: #endif /* _DEV_IC_RTL80x9_REG_H_ */
CVSweb