Annotation of sys/dev/ic/ncr53c9xreg.h, Revision 1.1
1.1 ! nbrk 1: /* $OpenBSD: ncr53c9xreg.h,v 1.9 2003/10/21 18:58:49 jmc Exp $ */
! 2: /* $NetBSD: ncr53c9xreg.h,v 1.4 1997/05/17 20:56:55 pk Exp $ */
! 3:
! 4: /*
! 5: * Copyright (c) 1994 Peter Galbavy. All rights reserved.
! 6: *
! 7: * Redistribution and use in source and binary forms, with or without
! 8: * modification, are permitted provided that the following conditions
! 9: * are met:
! 10: * 1. Redistributions of source code must retain the above copyright
! 11: * notice, this list of conditions and the following disclaimer.
! 12: * 2. Redistributions in binary form must reproduce the above copyright
! 13: * notice, this list of conditions and the following disclaimer in the
! 14: * documentation and/or other materials provided with the distribution.
! 15: *
! 16: * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
! 17: * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
! 18: * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
! 19: * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
! 20: * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
! 21: * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
! 22: * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
! 23: * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
! 24: * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
! 25: * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
! 26: */
! 27:
! 28: /*
! 29: * Register addresses, relative to some base address
! 30: */
! 31:
! 32: #define NCR_TCL 0x00 /* RW - Transfer Count Low */
! 33: #define NCR_TCM 0x01 /* RW - Transfer Count Mid */
! 34: #define NCR_TCH 0x0e /* RW - Transfer Count High */
! 35: /* NOT on 53C90 */
! 36:
! 37: #define NCR_FIFO 0x02 /* RW - FIFO data */
! 38:
! 39: #define NCR_CMD 0x03 /* RW - Command (2 deep) */
! 40: #define NCRCMD_DMA 0x80 /* DMA Bit */
! 41: #define NCRCMD_NOP 0x00 /* No Operation */
! 42: #define NCRCMD_FLUSH 0x01 /* Flush FIFO */
! 43: #define NCRCMD_RSTCHIP 0x02 /* Reset Chip */
! 44: #define NCRCMD_RSTSCSI 0x03 /* Reset SCSI Bus */
! 45: #define NCRCMD_RESEL 0x40 /* Reselect Sequence */
! 46: #define NCRCMD_SELNATN 0x41 /* Select without ATN */
! 47: #define NCRCMD_SELATN 0x42 /* Select with ATN */
! 48: #define NCRCMD_SELATNS 0x43 /* Select with ATN & Stop */
! 49: #define NCRCMD_ENSEL 0x44 /* Enable (Re)Selection */
! 50: #define NCRCMD_DISSEL 0x45 /* Disable (Re)Selection */
! 51: #define NCRCMD_SELATN3 0x46 /* Select with ATN3 */
! 52: #define NCRCMD_RESEL3 0x47 /* Reselect3 Sequence */
! 53: #define NCRCMD_SNDMSG 0x20 /* Send Message */
! 54: #define NCRCMD_SNDSTAT 0x21 /* Send Status */
! 55: #define NCRCMD_SNDDATA 0x22 /* Send Data */
! 56: #define NCRCMD_DISCSEQ 0x23 /* Disconnect Sequence */
! 57: #define NCRCMD_TERMSEQ 0x24 /* Terminate Sequence */
! 58: #define NCRCMD_TCCS 0x25 /* Target Command Comp Seq */
! 59: #define NCRCMD_DISC 0x27 /* Disconnect */
! 60: #define NCRCMD_RECMSG 0x28 /* Receive Message */
! 61: #define NCRCMD_RECCMD 0x29 /* Receive Command */
! 62: #define NCRCMD_RECDATA 0x2a /* Receive Data */
! 63: #define NCRCMD_RECCSEQ 0x2b /* Receive Command Sequence*/
! 64: #define NCRCMD_ABORT 0x04 /* Target Abort DMA */
! 65: #define NCRCMD_TRANS 0x10 /* Transfer Information */
! 66: #define NCRCMD_ICCS 0x11 /* Initiator Cmd Comp Seq */
! 67: #define NCRCMD_MSGOK 0x12 /* Message Accepted */
! 68: #define NCRCMD_TRPAD 0x18 /* Transfer Pad */
! 69: #define NCRCMD_SETATN 0x1a /* Set ATN */
! 70: #define NCRCMD_RSTATN 0x1b /* Reset ATN */
! 71:
! 72: #define NCR_STAT 0x04 /* RO - Status */
! 73: #define NCRSTAT_INT 0x80 /* Interrupt */
! 74: #define NCRSTAT_GE 0x40 /* Gross Error */
! 75: #define NCRSTAT_PE 0x20 /* Parity Error */
! 76: #define NCRSTAT_TC 0x10 /* Terminal Count */
! 77: #define NCRSTAT_VGC 0x08 /* Valid Group Code */
! 78: #define NCRSTAT_PHASE 0x07 /* Phase bits */
! 79:
! 80: #define NCR_SELID 0x04 /* WO - Select/Reselect Bus ID */
! 81: #define NCR_BUSID_HME 0x10 /* XXX HME reselect ID */
! 82: #define NCR_BUSID_HME32 0x40 /* XXX HME to select more than 16 */
! 83:
! 84: #define NCR_INTR 0x05 /* RO - Interrupt */
! 85: #define NCRINTR_SBR 0x80 /* SCSI Bus Reset */
! 86: #define NCRINTR_ILL 0x40 /* Illegal Command */
! 87: #define NCRINTR_DIS 0x20 /* Disconnect */
! 88: #define NCRINTR_BS 0x10 /* Bus Service */
! 89: #define NCRINTR_FC 0x08 /* Function Complete */
! 90: #define NCRINTR_RESEL 0x04 /* Reselected */
! 91: #define NCRINTR_SELATN 0x02 /* Select with ATN */
! 92: #define NCRINTR_SEL 0x01 /* Selected */
! 93:
! 94: #define NCR_TIMEOUT 0x05 /* WO - Select/Reselect Timeout */
! 95:
! 96: #define NCR_STEP 0x06 /* RO - Sequence Step */
! 97: #define NCRSTEP_MASK 0x07 /* the last 3 bits */
! 98: #define NCRSTEP_DONE 0x04 /* command went out */
! 99:
! 100: #define NCR_SYNCTP 0x06 /* WO - Synch Transfer Period */
! 101: /* Default 5 (53C9X) */
! 102:
! 103: #define NCR_FFLAG 0x07 /* RO - FIFO Flags */
! 104: #define NCRFIFO_SS 0xe0 /* Sequence Step (Dup) */
! 105: #define NCRFIFO_FF 0x1f /* Bytes in FIFO */
! 106:
! 107: #define NCR_SYNCOFF 0x07 /* WO - Synch Offset */
! 108: /* 0 = ASYNC */
! 109: /* 1 - 15 = SYNC bytes */
! 110:
! 111: #define NCR_CFG1 0x08 /* RW - Configuration #1 */
! 112: #define NCRCFG1_SLOW 0x80 /* Slow Cable Mode */
! 113: #define NCRCFG1_SRR 0x40 /* SCSI Reset Rep Int Dis */
! 114: #define NCRCFG1_PTEST 0x20 /* Parity Test Mod */
! 115: #define NCRCFG1_PARENB 0x10 /* Enable Parity Check */
! 116: #define NCRCFG1_CTEST 0x08 /* Enable Chip Test */
! 117: #define NCRCFG1_BUSID 0x07 /* Bus ID */
! 118:
! 119: #define NCR_CCF 0x09 /* WO - Clock Conversion Factor */
! 120: /* 0 = 35.01 - 40MHz */
! 121: /* NEVER SET TO 1 */
! 122: /* 2 = 10MHz */
! 123: /* 3 = 10.01 - 15MHz */
! 124: /* 4 = 15.01 - 20MHz */
! 125: /* 5 = 20.01 - 25MHz */
! 126: /* 6 = 25.01 - 30MHz */
! 127: /* 7 = 30.01 - 35MHz */
! 128:
! 129: #define NCR_TEST 0x0a /* WO - Test (Chip Test Only) */
! 130:
! 131: #define NCR_CFG2 0x0b /* RW - Configuration #2 */
! 132: #define NCRCFG2_RSVD 0xa0 /* reserved */
! 133: #define NCRCFG2_FE 0x40 /* Features Enable */
! 134: #define NCRCFG2_DREQ 0x10 /* DREQ High Impedance */
! 135: #define NCRCFG2_SCSI2 0x08 /* SCSI-2 Enable */
! 136: #define NCRCFG2_BPA 0x04 /* Target Bad Parity Abort */
! 137: #define NCRCFG2_RPE 0x02 /* Register Parity Error */
! 138: #define NCRCFG2_DPE 0x01 /* DMA Parity Error */
! 139: #define NCRCFG2_HMEFE 0x10 /* HME feature enable */
! 140: #define NCRCFG2_HME32 0x80 /* HME 32 extended */
! 141:
! 142: /* Config #3 only on 53C9X */
! 143: #define NCR_CFG3 0x0c /* RW - Configuration #3 */
! 144: #define NCRCFG3_RSVD 0xe0 /* reserved */
! 145: #define NCRCFG3_IDM 0x10 /* ID Message Res Check */
! 146: #define NCRCFG3_QTE 0x08 /* Queue Tag Enable */
! 147: #define NCRCFG3_CDB 0x04 /* CDB 10-bytes OK */
! 148: #define NCRCFG3_FSCSI 0x02 /* Fast SCSI */
! 149: #define NCRCFG3_FCLK 0x01 /* Fast Clock (>25MHz) */
! 150:
! 151: /*
! 152: * For some unknown reason, the ESP406/FAS408 looks like every
! 153: * other ncr53c9x, except for configuration #3 register. At any
! 154: * rate, if you're dealing with these chips, you need to use these
! 155: * defines instead.
! 156: */
! 157:
! 158: /* Config #3 different on ESP406/FAS408 */
! 159: #define NCR_ESPCFG3 0x0c /* RW - Configuration #3 */
! 160: #define NCRESPCFG3_IDM 0x80 /* ID Message Res Check */
! 161: #define NCRESPCFG3_QTE 0x40 /* Queue Tag Enable */
! 162: #define NCRESPCFG3_CDB 0x20 /* CDB 10-bytes OK */
! 163: #define NCRESPCFG3_FSCSI 0x10 /* Fast SCSI */
! 164: #define NCRESPCFG3_SRESB 0x08 /* Save Residual Byte */
! 165: #define NCRESPCFG3_FCLK 0x04 /* Fast Clock (>25MHz) */
! 166: #define NCRESPCFG3_ADMA 0x02 /* Alternate DMA Mode */
! 167: #define NCRESPCFG3_T8M 0x01 /* Threshold 8 Mode */
! 168:
! 169: /* Config #3 also different on NCR53CF9x/FAS216 */
! 170: #define NCR_F9XCFG3 0x0c /* RW - Configuration #3 */
! 171: #define NCRF9XCFG3_IDM 0x80 /* ID Message Res Check */
! 172: #define NCRF9XCFG3_QTE 0x40 /* Queue Tag Enable */
! 173: #define NCRF9XCFG3_CDB 0x20 /* CDB 10-bytes OK */
! 174: #define NCRF9XCFG3_FSCSI 0x10 /* Fast SCSI */
! 175: #define NCRF9XCFG3_FCLK 0x08 /* Fast Clock (>25MHz) */
! 176: #define NCRF9XCFG3_SRESB 0x04 /* Save Residual Byte */
! 177: #define NCRF9XCFG3_ADMA 0x02 /* Alternate DMA Mode */
! 178: #define NCRF9XCFG3_T8M 0x01 /* Threshold 8 Mode */
! 179:
! 180: /* Config #3 on FAS366 */
! 181: #define NCRFASCFG3_OBAUTO 0x80 /* auto push odd-byte to dma */
! 182: #define NCRFASCFG3_EWIDE 0x40 /* Enable Wide-SCSI */
! 183: #define NCRFASCFG3_IDBIT3 0x20 /* Bit 3 of HME SCSI-ID */
! 184: #define NCRFASCFG3_IDRESCHK 0x10 /* ID message checking */
! 185: #define NCRFASCFG3_QUENB 0x08 /* 3-byte msg support */
! 186: #define NCRFASCFG3_CDB10 0x04 /* group 2 scsi-2 support */
! 187: #define NCRFASCFG3_FASTSCSI 0x02 /* 10 MB/S fast scsi mode */
! 188: #define NCRFASCFG3_FASTCLK 0x01 /* fast clock mode */
! 189:
! 190: /* Config #4 only on ESP406/FAS408 */
! 191: #define NCR_CFG4 0x0d /* RW - Configuration #4 */
! 192: #define NCRCFG4_CRS1 0x80 /* Select register set #1 */
! 193: #define NCRCFG4_RSVD 0x7b /* reserved */
! 194: #define NCRCFG4_ACTNEG 0x04 /* Active negation */
! 195:
! 196: /*
! 197: The following registers are only on the ESP406/FAS408. The
! 198: documentation refers to them as "Control Register Set #1".
! 199: These are the registers that are visible when bit 7 of
! 200: register 0x0d is set. This bit is common to both register sets.
! 201: */
! 202:
! 203: #define NCR_JMP 0x00 /* RO - Jumper Sense Register */
! 204: #define NCRJMP_RSVD 0xc0 /* reserved */
! 205: #define NCRJMP_ROMSZ 0x20 /* ROM Size 1=16K, 0=32K */
! 206: #define NCRJMP_J4 0x10 /* Jumper #4 */
! 207: #define NCRJMP_J3 0x08 /* Jumper #3 */
! 208: #define NCRJMP_J2 0x04 /* Jumper #2 */
! 209: #define NCRJMP_J1 0x02 /* Jumper #1 */
! 210: #define NCRJMP_J0 0x01 /* Jumper #0 */
! 211:
! 212: #define NCR_PIOFIFO 0x04 /* WO - PIO FIFO, 4 bytes deep */
! 213:
! 214: #define NCR_PSTAT 0x08 /* RW - PIO Status Register */
! 215: #define NCRPSTAT_PERR 0x80 /* PIO Error */
! 216: #define NCRPSTAT_SIRQ 0x40 /* Active High of SCSI IRQ */
! 217: #define NCRPSTAT_ATAI 0x20 /* ATA IRQ */
! 218: #define NCRPSTAT_FEMPT 0x10 /* PIO FIFO Empty */
! 219: #define NCRPSTAT_F13 0x08 /* PIO FIFO 1/3 */
! 220: #define NCRPSTAT_F23 0x04 /* PIO FIFO 2/3 */
! 221: #define NCRPSTAT_FFULL 0x02 /* PIO FIFO Full */
! 222: #define NCRPSTAT_PIOM 0x01 /* PIO/DMA Mode */
! 223:
! 224: #define NCR_PIOI 0x0b /* RW - PIO Interrupt Enable */
! 225: #define NCRPIOI_RSVD 0xe0 /* reserved */
! 226: #define NCRPIOI_EMPTY 0x10 /* IRQ When Empty */
! 227: #define NCRPIOI_13 0x08 /* IRQ When 1/3 */
! 228: #define NCRPIOI_23 0x04 /* IRQ When 2/3 */
! 229: #define NCRPIOI_FULL 0x02 /* IRQ When Full */
! 230: #define NCRPIOI_FINV 0x01 /* Flag Invert */
! 231:
! 232: #define NCR_CFG5 0x0d /* RW - Configuration #5 */
! 233: #define NCRCFG5_CRS1 0x80 /* Select Register Set #1 */
! 234: #define NCRCFG5_SRAM 0x40 /* SRAM Memory Map */
! 235: #define NCRCFG5_AADDR 0x20 /* Auto Address */
! 236: #define NCRCFG5_PTRINC 0x10 /* Pointer Increment */
! 237: #define NCRCFG5_LOWPWR 0x08 /* Low Power Mode */
! 238: #define NCRCFG5_SINT 0x04 /* SCSI Interrupt Enable */
! 239: #define NCRCFG5_INTP 0x02 /* INT Polarity */
! 240: #define NCRCFG5_AINT 0x01 /* ATA Interrupt Enable */
! 241:
! 242: #define NCR_SIGNTR 0x0e /* RO - Signature */
! 243:
! 244: /* Am53c974 Config #3 */
! 245: #define NCR_AMDCFG3 0x0c /* RW - Configuration #3 */
! 246: #define NCRAMDCFG3_IDM 0x80 /* ID Message Res Check */
! 247: #define NCRAMDCFG3_QTE 0x40 /* Queue Tag Enable */
! 248: #define NCRAMDCFG3_CDB 0x20 /* CDB 10-bytes OK */
! 249: #define NCRAMDCFG3_FSCSI 0x10 /* Fast SCSI */
! 250: #define NCRAMDCFG3_FCLK 0x08 /* Fast Clock (40MHz) */
! 251: #define NCRAMDCFG3_RSVD 0x07 /* Reserved */
! 252:
! 253: /* Am53c974 Config #4 */
! 254: #define NCR_AMDCFG4 0x0d /* RW - Configuration #4 */
! 255: #define NCRAMDCFG4_GE 0xc0 /* Glitch Eater */
! 256: #define NCRAMDCFG4_GE12NS 0x00 /* Signal window 12ns */
! 257: #define NCRAMDCFG4_GE25NS 0x80 /* Signal window 25ns */
! 258: #define NCRAMDCFG4_GE35NS 0x40 /* Signal window 35ns */
! 259: #define NCRAMDCFG4_GE0NS 0xc0 /* Signal window 0ns */
! 260: #define NCRAMDCFG4_PWD 0x20 /* Reduced power feature */
! 261: #define NCRAMDCFG4_RSVD 0x13 /* Reserved */
! 262: #define NCRAMDCFG4_RAE 0x08 /* Active neg. REQ/ACK */
! 263: #define NCRAMDCFG4_RADE 0x04 /* Active neg. REQ/ACK/DAT */
! 264:
! 265: /*
! 266: * FAS366
! 267: */
! 268: #define NCR_RCL NCR_TCH /* Recommand counter low */
! 269: #define NCR_RCH 0xf /* Recommand counter high */
! 270: #define NCR_UID NCR_RCL /* fas366 part-uniq id */
! 271:
! 272: /* status register #2 definitions (read only) */
! 273: #define NCR_STAT2 NCR_CCF
! 274: #define FAS_STAT2_SEQCNT 0x01 /* Sequence counter bit 7-3 enabled */
! 275: #define FAS_STAT2_FLATCHED 0x02 /* FIFO flags register latched */
! 276: #define FAS_STAT2_CLATCHED 0x04 /* Xfer cntr & recommand ctr latched */
! 277: #define FAS_STAT2_CACTIVE 0x08 /* Command register is active */
! 278: #define FAS_STAT2_SCSI16 0x10 /* SCSI interface is wide */
! 279: #define FAS_STAT2_ISHUTTLE 0x20 /* FIFO Top register contains 1 byte */
! 280: #define FAS_STAT2_OSHUTTLE 0x40 /* next byte from FIFO is MSB */
! 281: #define FAS_STAT2_EMPTY 0x80 /* FIFO is empty */
CVSweb