/* $OpenBSD: max2820reg.h,v 1.1 2004/12/29 01:02:31 jsg Exp $ */
/* $NetBSD: max2820reg.h,v 1.1 2004/09/26 02:29:15 dyoung Exp $ */
/*
* Copyright (c) 2004 David Young. All rights reserved.
*
* This code was written by David Young.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. Neither the name of the author nor the names of any co-contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY David Young ``AS IS'' AND ANY
* EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
* THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
* PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL David
* Young BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
* EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
* TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
* OF SUCH DAMAGE.
*/
#ifndef _DEV_IC_MAX2820REG_H_
#define _DEV_IC_MAX2820REG_H_
/*
* Serial bus format for Maxim MAX2820/MAX2820A/MAX2821/MAX2821A
* 2.4GHz 802.11b Zero-IF Transceivers
*/
#define MAX2820_TWI_ADDR_MASK BITS(15,12)
#define MAX2820_TWI_DATA_MASK BITS(11,0)
/*
* Registers for Maxim MAX2820/MAX2820A/MAX2821/MAX2821A 2.4GHz
* 802.11b Zero-IF Transceivers
*/
#define MAX2820_TEST 0 /* Test Register */
#define MAX2820_TEST_DEFAULT BITS(2,0) /* Always set to this value. */
#define MAX2820_ENABLE 1 /* Block-Enable Register */
#define MAX2820_ENABLE_RSVD1 BIT(11) /* reserved */
#define MAX2820_ENABLE_PAB BIT(10) /* Transmit Baseband Filters
* Enable
* PAB_EN = SHDNB &&
* (MAX2820_ENABLE_PAB ||
* TX_ON)
*/
#define MAX2820_ENABLE_TXFLT BIT(9) /* Transmit Baseband Filters
* Enable
* TXFLT_EN = SHDNB &&
* (MAX2820_ENABLE_TXFLT ||
* TX_ON)
*/
#define MAX2820_ENABLE_TXUVD BIT(8) /* Tx Upconverter, VGA, and
* Driver Amp Enable
* TXUVD_EN = SHDNB &&
* (MAX2820_ENABLE_TXUVD ||
* TX_ON)
*/
#define MAX2820_ENABLE_DET BIT(7) /* Receive Detector Enable
* DET_EN = SHDNB &&
* (MAX2820_ENABLE_DET ||
* RX_ON)
*/
#define MAX2820_ENABLE_RXDFA BIT(6) /* Rx Downconverter, Filters,
* and AGC Amps Enable
* RXDFA_EN = SHDNB &&
* (MAX2820_ENABLE_RXDFA ||
* RX_ON)
*/
#define MAX2820_ENABLE_RXLNA BIT(5) /* Receive LNA Enable
* AT_EN = SHDNB &&
* (MAX2820_ENABLE_RXLNA ||
* RX_ON)
*/
#define MAX2820_ENABLE_AT BIT(4) /* Auto-tuner Enable
* AT_EN = SHDNB &&
* (MAX2820_ENABLE_AT ||
* RX_ON || TX_ON)
*/
#define MAX2820_ENABLE_CP BIT(3) /* PLL Charge-Pump Enable
* CP_EN = SHDNB
* && MAX2820_ENABLE_CP
*/
#define MAX2820_ENABLE_PLL BIT(2) /* PLL Enable
* PLL_EN = SHDNB
* && MAX2820_ENABLE_PLL
*/
#define MAX2820_ENABLE_VCO BIT(1) /* VCO Enable
* VCO_EN = SHDNB
* && MAX2820_ENABLE_VCO
*/
#define MAX2820_ENABLE_RSVD0 BIT(0) /* reserved */
#define MAX2820_ENABLE_DEFAULT (MAX2820_ENABLE_AT|MAX2820_ENABLE_CP|\
MAX2820_ENABLE_PLL|MAX2820_ENABLE_VCO)
#define MAX2820_SYNTH 2 /* Synthesizer Register */
#define MAX2820_SYNTH_RSVD0 BITS(11,7) /* reserved */
#define MAX2820_SYNTH_ICP BIT(6) /* Charge-Pump Current Select
* 0 = +/-1mA
* 1 = +/-2mA
*/
#define MAX2820_SYNTH_R_MASK BITS(5,0) /* Reference Frequency Divider
* 0 = 22MHz
* 1 = 44MHz
*/
#define MAX2820_SYNTH_R_22MHZ LSHIFT(0, MAX2820_SYNTH_R_MASK)
#define MAX2820_SYNTH_R_44MHZ LSHIFT(1, MAX2820_SYNTH_R_MASK)
#define MAX2820_SYNTH_ICP_DEFAULT MAX2820_SYNTH_ICP
#define MAX2820_SYNTH_R_DEFAULT LSHIFT(0, MAX2820_SYNTH_R_MASK)
#define MAX2820_CHANNEL 3 /* Channel Frequency Register */
#define MAX2820_CHANNEL_RSVD BITS(11,7) /* reserved */
#define MAX2820_CHANNEL_CF_MASK BITS(6,0) /* Channel Frequency Select
* fLO = 2400MHz + CF * 1MHz
*/
#define MAX2820_CHANNEL_RSVD_DEFAULT LSHIFT(0, MAX2820_CHANNEL_RSVD)
#define MAX2820_CHANNEL_CF_DEFAULT LSHIFT(37, MAX2820_CHANNEL_CF_MASK)
#define MAX2820_RECEIVE 4 /* Receiver Settings Register
* MAX2820/MAX2821
*/
#define MAX2820_RECEIVE_2C_MASK BITS(11,9) /* VGA DC Offset Nulling
* Parameter 2
*/
#define MAX2820_RECEIVE_1C_MASK BITS(8,6) /* VGA DC Offset Nulling
* Parameter 1
*/
#define MAX2820_RECEIVE_DL_MASK BITS(5,4) /* Rx Level Detector Midpoint
* Select
* 11, 01 = 50.2mVp
* 10 = 70.9mVp
* 00 = 35.5mVp
*/
#define MAX2820_RECEIVE_SF BIT(3) /* Special Function Select
* 0 = OFF
* 1 = ON
*/
#define MAX2820_RECEIVE_BW_MASK BITS(2,0) /* Receive Filter -3dB Frequency
* Select (all frequencies are
* approximate)
*/
/* 8.5MHz */
#define MAX2820_RECEIVE_BW_8_5MHZ LSHIFT(0, MAX2820_RECEIVE_BW_MASK)
#define MAX2820_RECEIVE_BW_8MHZ LSHIFT(1, MAX2820_RECEIVE_BW_MASK)
#define MAX2820_RECEIVE_BW_7_5MHZ LSHIFT(2, MAX2820_RECEIVE_BW_MASK)
#define MAX2820_RECEIVE_BW_7MHZ LSHIFT(3, MAX2820_RECEIVE_BW_MASK)
#define MAX2820_RECEIVE_BW_6_5MHZ LSHIFT(4, MAX2820_RECEIVE_BW_MASK)
#define MAX2820_RECEIVE_BW_6MHZ LSHIFT(5, MAX2820_RECEIVE_BW_MASK)
#define MAX2820_RECEIVE_2C_DEFAULT LSHIFT(7, MAX2820_RECEIVE_2C_MASK)
#define MAX2820_RECEIVE_1C_DEFAULT LSHIFT(7, MAX2820_RECEIVE_1C_MASK)
#define MAX2820_RECEIVE_DL_DEFAULT LSHIFT(1, MAX2820_RECEIVE_DL_MASK)
#define MAX2820_RECEIVE_SF_DEFAULT LSHIFT(0, MAX2820_RECEIVE_SF)
#define MAX2820_RECEIVE_BW_DEFAULT MAX2820_RECEIVE_BW_7_5MHZ
#define MAX2820A_RECEIVE 4 /* Receiver Settings Register,
* MAX2820A/MAX2821A
*/
/* VGA DC Offset Nulling Parameter 2 */
#define MAX2820A_RECEIVE_2C_MASK BITS(11,9)
#define MAX2820A_RECEIVE_2C_DEFAULT LSHIFT(7, MAX2820A_RECEIVE_2C_MASK)
/* VGA DC Offset Nulling Parameter 1 */
#define MAX2820A_RECEIVE_1C_MASK BITS(8,6)
#define MAX2820A_RECEIVE_1C_DEFAULT LSHIFT(7, MAX2820A_RECEIVE_1C_MASK)
#define MAX2820A_RECEIVE_RSVD0_MASK BITS(5,3)
#define MAX2820A_RECEIVE_RSVD0_DEFAULT LSHIFT(2, MAX2820A_RECEIVE_RSVD0_MASK)
#define MAX2820A_RECEIVE_RSVD1_MASK BITS(2,0)
#define MAX2820A_RECEIVE_RSVD1_DEFAULT LSHIFT(2,MAX2820_RECEIVE_RSVD1_MASK)
#define MAX2820_TRANSMIT 5 /* Transmitter Settings Reg. */
#define MAX2820_TRANSMIT_RSVD_MASK BITS(11,4) /* reserved */
#define MAX2820_TRANSMIT_PA_MASK BITS(3,0) /* PA Bias Select
* 15 = Highest
* 0 = Lowest
*/
#define MAX2820_TRANSMIT_PA_DEFAULT LSHIFT(0, MAX2820_TRANSMIT_PA_MASK)
#endif /* _DEV_IC_MAX2820REG_H_ */
![[BACK]](/icons/back.gif){kind=icon}
Return to max2820reg.h CVS log ![[TXT]](/icons/text.gif){kind=icon}
![[DIR]](/icons/dir.gif){kind=icon}
Up to [local] / sys / dev / ic