Annotation of sys/dev/ic/ispreg.h, Revision 1.1
1.1 ! nbrk 1: /* $OpenBSD: ispreg.h,v 1.13 2003/10/21 18:58:49 jmc Exp $ */
! 2: /*
! 3: * Machine Independent (well, as best as possible) register
! 4: * definitions for Qlogic ISP SCSI adapters.
! 5: *
! 6: * Copyright (c) 1997, 1998, 1999, 2000 by Matthew Jacob
! 7: * All rights reserved.
! 8: *
! 9: * Redistribution and use in source and binary forms, with or without
! 10: * modification, are permitted provided that the following conditions
! 11: * are met:
! 12: * 1. Redistributions of source code must retain the above copyright
! 13: * notice immediately at the beginning of the file, without modification,
! 14: * this list of conditions, and the following disclaimer.
! 15: * 2. The name of the author may not be used to endorse or promote products
! 16: * derived from this software without specific prior written permission.
! 17: *
! 18: * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
! 19: * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
! 20: * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
! 21: * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
! 22: * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
! 23: * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
! 24: * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
! 25: * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
! 26: * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
! 27: * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
! 28: * SUCH DAMAGE.
! 29: */
! 30: #ifndef _ISPREG_H
! 31: #define _ISPREG_H
! 32:
! 33: /*
! 34: * Hardware definitions for the Qlogic ISP registers.
! 35: */
! 36:
! 37: /*
! 38: * This defines types of access to various registers.
! 39: *
! 40: * R: Read Only
! 41: * W: Write Only
! 42: * RW: Read/Write
! 43: *
! 44: * R*, W*, RW*: Read Only, Write Only, Read/Write, but only
! 45: * if RISC processor in ISP is paused.
! 46: */
! 47:
! 48: /*
! 49: * Offsets for various register blocks.
! 50: *
! 51: * Sad but true, different architectures have different offsets.
! 52: *
! 53: * Don't be alarmed if none of this makes sense. The original register
! 54: * layout set some defines in a certain pattern. Everything else has been
! 55: * grafted on since. For example, the ISP1080 manual will state that DMA
! 56: * registers start at 0x80 from the base of the register address space.
! 57: * That's true, but for our purposes, we define DMA_REGS_OFF for the 1080
! 58: * to start at offset 0x60 because the DMA registers are all defined to
! 59: * be DMA_BLOCK+0x20 and so on. Clear?
! 60: */
! 61:
! 62: #define BIU_REGS_OFF 0x00
! 63:
! 64: #define PCI_MBOX_REGS_OFF 0x70
! 65: #define PCI_MBOX_REGS2100_OFF 0x10
! 66: #define PCI_MBOX_REGS2300_OFF 0x40
! 67: #define SBUS_MBOX_REGS_OFF 0x80
! 68:
! 69: #define PCI_SXP_REGS_OFF 0x80
! 70: #define SBUS_SXP_REGS_OFF 0x200
! 71:
! 72: #define PCI_RISC_REGS_OFF 0x80
! 73: #define SBUS_RISC_REGS_OFF 0x400
! 74:
! 75: /* Bless me! Chip designers have putzed it again! */
! 76: #define ISP1080_DMA_REGS_OFF 0x60
! 77: #define DMA_REGS_OFF 0x00 /* same as BIU block */
! 78:
! 79: #define SBUS_REGSIZE 0x450
! 80: #define PCI_REGSIZE 0x100
! 81:
! 82: /*
! 83: * NB: The *_BLOCK definitions have no specific hardware meaning.
! 84: * They serve simply to note to the MD layer which block of
! 85: * registers offsets are being accessed.
! 86: */
! 87: #define _NREG_BLKS 5
! 88: #define _BLK_REG_SHFT 13
! 89: #define _BLK_REG_MASK (7 << _BLK_REG_SHFT)
! 90: #define BIU_BLOCK (0 << _BLK_REG_SHFT)
! 91: #define MBOX_BLOCK (1 << _BLK_REG_SHFT)
! 92: #define SXP_BLOCK (2 << _BLK_REG_SHFT)
! 93: #define RISC_BLOCK (3 << _BLK_REG_SHFT)
! 94: #define DMA_BLOCK (4 << _BLK_REG_SHFT)
! 95:
! 96: /*
! 97: * Bus Interface Block Register Offsets
! 98: */
! 99:
! 100: #define BIU_ID_LO (BIU_BLOCK+0x0) /* R : Bus ID, Low */
! 101: #define BIU2100_FLASH_ADDR (BIU_BLOCK+0x0)
! 102: #define BIU_ID_HI (BIU_BLOCK+0x2) /* R : Bus ID, High */
! 103: #define BIU2100_FLASH_DATA (BIU_BLOCK+0x2)
! 104: #define BIU_CONF0 (BIU_BLOCK+0x4) /* R : Bus Configuration #0 */
! 105: #define BIU_CONF1 (BIU_BLOCK+0x6) /* R : Bus Configuration #1 */
! 106: #define BIU2100_CSR (BIU_BLOCK+0x6)
! 107: #define BIU_ICR (BIU_BLOCK+0x8) /* RW : Bus Interface Ctrl */
! 108: #define BIU_ISR (BIU_BLOCK+0xA) /* R : Bus Interface Status */
! 109: #define BIU_SEMA (BIU_BLOCK+0xC) /* RW : Bus Semaphore */
! 110: #define BIU_NVRAM (BIU_BLOCK+0xE) /* RW : Bus NVRAM */
! 111: /*
! 112: * These are specific to the 2300.
! 113: *
! 114: * They *claim* you can read BIU_R2HSTSLO with a full 32 bit access
! 115: * and get both registers, but I'm a bit dubious about that. But the
! 116: * point here is that the top 16 bits are firmware defined bits that
! 117: * the RISC processor uses to inform the host about something- usually
! 118: * something which was nominally in a mailbox register.
! 119: */
! 120: #define BIU_REQINP (BIU_BLOCK+0x10) /* Request Queue In */
! 121: #define BIU_REQOUTP (BIU_BLOCK+0x12) /* Request Queue Out */
! 122: #define BIU_RSPINP (BIU_BLOCK+0x14) /* Response Queue In */
! 123: #define BIU_RSPOUTP (BIU_BLOCK+0x16) /* Response Queue Out */
! 124:
! 125: #define BIU_R2HSTSLO (BIU_BLOCK+0x18)
! 126: #define BIU_R2HSTSHI (BIU_BLOCK+0x1A)
! 127:
! 128: #define BIU_R2HST_INTR (1 << 15) /* RISC to Host Interrupt */
! 129: #define BIU_R2HST_PAUSED (1 << 8) /* RISC paused */
! 130: #define BIU_R2HST_ISTAT_MASK 0x3f /* intr information && status */
! 131: #define ISPR2HST_ROM_MBX_OK 0x1 /* ROM mailbox cmd done ok */
! 132: #define ISPR2HST_ROM_MBX_FAIL 0x2 /* ROM mailbox cmd done fail */
! 133: #define ISPR2HST_MBX_OK 0x10 /* mailbox cmd done ok */
! 134: #define ISPR2HST_MBX_FAIL 0x11 /* mailbox cmd done fail */
! 135: #define ISPR2HST_ASYNC_EVENT 0x12 /* Async Event */
! 136: #define ISPR2HST_RSPQ_UPDATE 0x13 /* Response Queue Update */
! 137: #define ISPR2HST_RQST_UPDATE 0x14 /* Resquest Queue Update */
! 138: #define ISPR2HST_RIO_16 0x15 /* RIO 1-16 */
! 139: #define ISPR2HST_FPOST 0x16 /* Low 16 bits fast post */
! 140: #define ISPR2HST_FPOST_CTIO 0x17 /* Low 16 bits fast post ctio */
! 141:
! 142: #define DFIFO_COMMAND (BIU_BLOCK+0x60) /* RW : Command FIFO Port */
! 143: #define RDMA2100_CONTROL DFIFO_COMMAND
! 144: #define DFIFO_DATA (BIU_BLOCK+0x62) /* RW : Data FIFO Port */
! 145:
! 146: /*
! 147: * Putzed DMA register layouts.
! 148: */
! 149: #define CDMA_CONF (DMA_BLOCK+0x20) /* RW*: DMA Configuration */
! 150: #define CDMA2100_CONTROL CDMA_CONF
! 151: #define CDMA_CONTROL (DMA_BLOCK+0x22) /* RW*: DMA Control */
! 152: #define CDMA_STATUS (DMA_BLOCK+0x24) /* R : DMA Status */
! 153: #define CDMA_FIFO_STS (DMA_BLOCK+0x26) /* R : DMA FIFO Status */
! 154: #define CDMA_COUNT (DMA_BLOCK+0x28) /* RW*: DMA Transfer Count */
! 155: #define CDMA_ADDR0 (DMA_BLOCK+0x2C) /* RW*: DMA Address, Word 0 */
! 156: #define CDMA_ADDR1 (DMA_BLOCK+0x2E) /* RW*: DMA Address, Word 1 */
! 157: #define CDMA_ADDR2 (DMA_BLOCK+0x30) /* RW*: DMA Address, Word 2 */
! 158: #define CDMA_ADDR3 (DMA_BLOCK+0x32) /* RW*: DMA Address, Word 3 */
! 159:
! 160: #define DDMA_CONF (DMA_BLOCK+0x40) /* RW*: DMA Configuration */
! 161: #define TDMA2100_CONTROL DDMA_CONF
! 162: #define DDMA_CONTROL (DMA_BLOCK+0x42) /* RW*: DMA Control */
! 163: #define DDMA_STATUS (DMA_BLOCK+0x44) /* R : DMA Status */
! 164: #define DDMA_FIFO_STS (DMA_BLOCK+0x46) /* R : DMA FIFO Status */
! 165: #define DDMA_COUNT_LO (DMA_BLOCK+0x48) /* RW*: DMA Xfer Count, Low */
! 166: #define DDMA_COUNT_HI (DMA_BLOCK+0x4A) /* RW*: DMA Xfer Count, High */
! 167: #define DDMA_ADDR0 (DMA_BLOCK+0x4C) /* RW*: DMA Address, Word 0 */
! 168: #define DDMA_ADDR1 (DMA_BLOCK+0x4E) /* RW*: DMA Address, Word 1 */
! 169: /* these are for the 1040A cards */
! 170: #define DDMA_ADDR2 (DMA_BLOCK+0x50) /* RW*: DMA Address, Word 2 */
! 171: #define DDMA_ADDR3 (DMA_BLOCK+0x52) /* RW*: DMA Address, Word 3 */
! 172:
! 173:
! 174: /*
! 175: * Bus Interface Block Register Definitions
! 176: */
! 177: /* BUS CONFIGURATION REGISTER #0 */
! 178: #define BIU_CONF0_HW_MASK 0x000F /* Hardware revision mask */
! 179: /* BUS CONFIGURATION REGISTER #1 */
! 180:
! 181: #define BIU_SBUS_CONF1_PARITY 0x0100 /* Enable parity checking */
! 182: #define BIU_SBUS_CONF1_FCODE_MASK 0x00F0 /* Fcode cycle mask */
! 183:
! 184: #define BIU_PCI_CONF1_FIFO_128 0x0040 /* 128 bytes FIFO threshold */
! 185: #define BIU_PCI_CONF1_FIFO_64 0x0030 /* 64 bytes FIFO threshold */
! 186: #define BIU_PCI_CONF1_FIFO_32 0x0020 /* 32 bytes FIFO threshold */
! 187: #define BIU_PCI_CONF1_FIFO_16 0x0010 /* 16 bytes FIFO threshold */
! 188: #define BIU_BURST_ENABLE 0x0004 /* Global enable Bus bursts */
! 189: #define BIU_SBUS_CONF1_FIFO_64 0x0003 /* 64 bytes FIFO threshold */
! 190: #define BIU_SBUS_CONF1_FIFO_32 0x0002 /* 32 bytes FIFO threshold */
! 191: #define BIU_SBUS_CONF1_FIFO_16 0x0001 /* 16 bytes FIFO threshold */
! 192: #define BIU_SBUS_CONF1_FIFO_8 0x0000 /* 8 bytes FIFO threshold */
! 193: #define BIU_SBUS_CONF1_BURST8 0x0008 /* Enable 8-byte bursts */
! 194: #define BIU_PCI_CONF1_SXP 0x0008 /* SXP register select */
! 195:
! 196: #define BIU_PCI1080_CONF1_SXP0 0x0100 /* SXP bank #1 select */
! 197: #define BIU_PCI1080_CONF1_SXP1 0x0200 /* SXP bank #2 select */
! 198: #define BIU_PCI1080_CONF1_DMA 0x0300 /* DMA bank select */
! 199:
! 200: /* ISP2100 Bus Control/Status Register */
! 201:
! 202: #define BIU2100_ICSR_REGBSEL 0x30 /* RW: register bank select */
! 203: #define BIU2100_RISC_REGS (0 << 4) /* RISC Regs */
! 204: #define BIU2100_FB_REGS (1 << 4) /* FrameBuffer Regs */
! 205: #define BIU2100_FPM0_REGS (2 << 4) /* FPM 0 Regs */
! 206: #define BIU2100_FPM1_REGS (3 << 4) /* FPM 1 Regs */
! 207: #define BIU2100_PCI64 0x04 /* R: 64 Bit PCI slot */
! 208: #define BIU2100_FLASH_ENABLE 0x02 /* RW: Enable Flash RAM */
! 209: #define BIU2100_SOFT_RESET 0x01
! 210: /* SOFT RESET FOR ISP2100 is same bit, but in this register, not ICR */
! 211:
! 212:
! 213: /* BUS CONTROL REGISTER */
! 214: #define BIU_ICR_ENABLE_DMA_INT 0x0020 /* Enable DMA interrupts */
! 215: #define BIU_ICR_ENABLE_CDMA_INT 0x0010 /* Enable CDMA interrupts */
! 216: #define BIU_ICR_ENABLE_SXP_INT 0x0008 /* Enable SXP interrupts */
! 217: #define BIU_ICR_ENABLE_RISC_INT 0x0004 /* Enable Risc interrupts */
! 218: #define BIU_ICR_ENABLE_ALL_INTS 0x0002 /* Global enable all inter */
! 219: #define BIU_ICR_SOFT_RESET 0x0001 /* Soft Reset of ISP */
! 220:
! 221: #define BIU2100_ICR_ENABLE_ALL_INTS 0x8000
! 222: #define BIU2100_ICR_ENA_FPM_INT 0x0020
! 223: #define BIU2100_ICR_ENA_FB_INT 0x0010
! 224: #define BIU2100_ICR_ENA_RISC_INT 0x0008
! 225: #define BIU2100_ICR_ENA_CDMA_INT 0x0004
! 226: #define BIU2100_ICR_ENABLE_RXDMA_INT 0x0002
! 227: #define BIU2100_ICR_ENABLE_TXDMA_INT 0x0001
! 228: #define BIU2100_ICR_DISABLE_ALL_INTS 0x0000
! 229:
! 230: #define ENABLE_INTS(isp) (IS_SCSI(isp))? \
! 231: ISP_WRITE(isp, BIU_ICR, BIU_ICR_ENABLE_RISC_INT | BIU_ICR_ENABLE_ALL_INTS) : \
! 232: ISP_WRITE(isp, BIU_ICR, BIU2100_ICR_ENA_RISC_INT | BIU2100_ICR_ENABLE_ALL_INTS)
! 233:
! 234: #define INTS_ENABLED(isp) ((IS_SCSI(isp))? \
! 235: (ISP_READ(isp, BIU_ICR) & (BIU_ICR_ENABLE_RISC_INT|BIU_ICR_ENABLE_ALL_INTS)) :\
! 236: (ISP_READ(isp, BIU_ICR) & \
! 237: (BIU2100_ICR_ENA_RISC_INT|BIU2100_ICR_ENABLE_ALL_INTS)))
! 238:
! 239: #define DISABLE_INTS(isp) ISP_WRITE(isp, BIU_ICR, 0)
! 240:
! 241: /* BUS STATUS REGISTER */
! 242: #define BIU_ISR_DMA_INT 0x0020 /* DMA interrupt pending */
! 243: #define BIU_ISR_CDMA_INT 0x0010 /* CDMA interrupt pending */
! 244: #define BIU_ISR_SXP_INT 0x0008 /* SXP interrupt pending */
! 245: #define BIU_ISR_RISC_INT 0x0004 /* Risc interrupt pending */
! 246: #define BIU_ISR_IPEND 0x0002 /* Global interrupt pending */
! 247:
! 248: #define BIU2100_ISR_INT_PENDING 0x8000 /* Global interrupt pending */
! 249: #define BIU2100_ISR_FPM_INT 0x0020 /* FPM interrupt pending */
! 250: #define BIU2100_ISR_FB_INT 0x0010 /* FB interrupt pending */
! 251: #define BIU2100_ISR_RISC_INT 0x0008 /* Risc interrupt pending */
! 252: #define BIU2100_ISR_CDMA_INT 0x0004 /* CDMA interrupt pending */
! 253: #define BIU2100_ISR_RXDMA_INT_PENDING 0x0002 /* Global interrupt pending */
! 254: #define BIU2100_ISR_TXDMA_INT_PENDING 0x0001 /* Global interrupt pending */
! 255:
! 256: #define INT_PENDING(isp, isr) (IS_FC(isp)? \
! 257: ((isr & BIU2100_ISR_RISC_INT) != 0) : ((isr & BIU_ISR_RISC_INT) != 0))
! 258:
! 259: #define INT_PENDING_MASK(isp) \
! 260: (IS_FC(isp)? BIU2100_ISR_RISC_INT: BIU_ISR_RISC_INT)
! 261:
! 262: /* BUS SEMAPHORE REGISTER */
! 263: #define BIU_SEMA_STATUS 0x0002 /* Semaphore Status Bit */
! 264: #define BIU_SEMA_LOCK 0x0001 /* Semaphore Lock Bit */
! 265:
! 266: /* NVRAM SEMAPHORE REGISTER */
! 267: #define BIU_NVRAM_CLOCK 0x0001
! 268: #define BIU_NVRAM_SELECT 0x0002
! 269: #define BIU_NVRAM_DATAOUT 0x0004
! 270: #define BIU_NVRAM_DATAIN 0x0008
! 271: #define ISP_NVRAM_READ 6
! 272:
! 273: /* COMNMAND && DATA DMA CONFIGURATION REGISTER */
! 274: #define DMA_ENABLE_SXP_DMA 0x0008 /* Enable SXP to DMA Data */
! 275: #define DMA_ENABLE_INTS 0x0004 /* Enable interrupts to RISC */
! 276: #define DMA_ENABLE_BURST 0x0002 /* Enable Bus burst trans */
! 277: #define DMA_DMA_DIRECTION 0x0001 /*
! 278: * Set DMA direction:
! 279: * 0 - DMA FIFO to host
! 280: * 1 - Host to DMA FIFO
! 281: */
! 282:
! 283: /* COMMAND && DATA DMA CONTROL REGISTER */
! 284: #define DMA_CNTRL_SUSPEND_CHAN 0x0010 /* Suspend DMA transfer */
! 285: #define DMA_CNTRL_CLEAR_CHAN 0x0008 /*
! 286: * Clear FIFO and DMA Channel,
! 287: * reset DMA registers
! 288: */
! 289: #define DMA_CNTRL_CLEAR_FIFO 0x0004 /* Clear DMA FIFO */
! 290: #define DMA_CNTRL_RESET_INT 0x0002 /* Clear DMA interrupt */
! 291: #define DMA_CNTRL_STROBE 0x0001 /* Start DMA transfer */
! 292:
! 293: /*
! 294: * Variants of same for 2100
! 295: */
! 296: #define DMA_CNTRL2100_CLEAR_CHAN 0x0004
! 297: #define DMA_CNTRL2100_RESET_INT 0x0002
! 298:
! 299:
! 300:
! 301: /* DMA STATUS REGISTER */
! 302: #define DMA_SBUS_STATUS_PIPE_MASK 0x00C0 /* DMA Pipeline status mask */
! 303: #define DMA_SBUS_STATUS_CHAN_MASK 0x0030 /* Channel status mask */
! 304: #define DMA_SBUS_STATUS_BUS_PARITY 0x0008 /* Parity Error on bus */
! 305: #define DMA_SBUS_STATUS_BUS_ERR 0x0004 /* Error Detected on bus */
! 306: #define DMA_SBUS_STATUS_TERM_COUNT 0x0002 /* DMA Transfer Completed */
! 307: #define DMA_SBUS_STATUS_INTERRUPT 0x0001 /* Enable DMA channel inter */
! 308:
! 309: #define DMA_PCI_STATUS_INTERRUPT 0x8000 /* Enable DMA channel inter */
! 310: #define DMA_PCI_STATUS_RETRY_STAT 0x4000 /* Retry status */
! 311: #define DMA_PCI_STATUS_CHAN_MASK 0x3000 /* Channel status mask */
! 312: #define DMA_PCI_STATUS_FIFO_OVR 0x0100 /* DMA FIFO overrun cond */
! 313: #define DMA_PCI_STATUS_FIFO_UDR 0x0080 /* DMA FIFO underrun cond */
! 314: #define DMA_PCI_STATUS_BUS_ERR 0x0040 /* Error Detected on bus */
! 315: #define DMA_PCI_STATUS_BUS_PARITY 0x0020 /* Parity Error on bus */
! 316: #define DMA_PCI_STATUS_CLR_PEND 0x0010 /* DMA clear pending */
! 317: #define DMA_PCI_STATUS_TERM_COUNT 0x0008 /* DMA Transfer Completed */
! 318: #define DMA_PCI_STATUS_DMA_SUSP 0x0004 /* DMA suspended */
! 319: #define DMA_PCI_STATUS_PIPE_MASK 0x0003 /* DMA Pipeline status mask */
! 320:
! 321: /* DMA Status Register, pipeline status bits */
! 322: #define DMA_SBUS_PIPE_FULL 0x00C0 /* Both pipeline stages full */
! 323: #define DMA_SBUS_PIPE_OVERRUN 0x0080 /* Pipeline overrun */
! 324: #define DMA_SBUS_PIPE_STAGE1 0x0040 /*
! 325: * Pipeline stage 1 Loaded,
! 326: * stage 2 empty
! 327: */
! 328: #define DMA_PCI_PIPE_FULL 0x0003 /* Both pipeline stages full */
! 329: #define DMA_PCI_PIPE_OVERRUN 0x0002 /* Pipeline overrun */
! 330: #define DMA_PCI_PIPE_STAGE1 0x0001 /*
! 331: * Pipeline stage 1 Loaded,
! 332: * stage 2 empty
! 333: */
! 334: #define DMA_PIPE_EMPTY 0x0000 /* All pipeline stages empty */
! 335:
! 336: /* DMA Status Register, channel status bits */
! 337: #define DMA_SBUS_CHAN_SUSPEND 0x0030 /* Channel error or suspended */
! 338: #define DMA_SBUS_CHAN_TRANSFER 0x0020 /* Chan transfer in progress */
! 339: #define DMA_SBUS_CHAN_ACTIVE 0x0010 /* Chan trans to host active */
! 340: #define DMA_PCI_CHAN_TRANSFER 0x3000 /* Chan transfer in progress */
! 341: #define DMA_PCI_CHAN_SUSPEND 0x2000 /* Channel error or suspended */
! 342: #define DMA_PCI_CHAN_ACTIVE 0x1000 /* Chan trans to host active */
! 343: #define ISP_DMA_CHAN_IDLE 0x0000 /* Chan idle (normal comp) */
! 344:
! 345:
! 346: /* DMA FIFO STATUS REGISTER */
! 347: #define DMA_FIFO_STATUS_OVERRUN 0x0200 /* FIFO Overrun Condition */
! 348: #define DMA_FIFO_STATUS_UNDERRUN 0x0100 /* FIFO Underrun Condition */
! 349: #define DMA_FIFO_SBUS_COUNT_MASK 0x007F /* FIFO Byte count mask */
! 350: #define DMA_FIFO_PCI_COUNT_MASK 0x00FF /* FIFO Byte count mask */
! 351:
! 352: /*
! 353: * Mailbox Block Register Offsets
! 354: */
! 355:
! 356: #define INMAILBOX0 (MBOX_BLOCK+0x0)
! 357: #define INMAILBOX1 (MBOX_BLOCK+0x2)
! 358: #define INMAILBOX2 (MBOX_BLOCK+0x4)
! 359: #define INMAILBOX3 (MBOX_BLOCK+0x6)
! 360: #define INMAILBOX4 (MBOX_BLOCK+0x8)
! 361: #define INMAILBOX5 (MBOX_BLOCK+0xA)
! 362: #define INMAILBOX6 (MBOX_BLOCK+0xC)
! 363: #define INMAILBOX7 (MBOX_BLOCK+0xE)
! 364:
! 365: #define OUTMAILBOX0 (MBOX_BLOCK+0x0)
! 366: #define OUTMAILBOX1 (MBOX_BLOCK+0x2)
! 367: #define OUTMAILBOX2 (MBOX_BLOCK+0x4)
! 368: #define OUTMAILBOX3 (MBOX_BLOCK+0x6)
! 369: #define OUTMAILBOX4 (MBOX_BLOCK+0x8)
! 370: #define OUTMAILBOX5 (MBOX_BLOCK+0xA)
! 371: #define OUTMAILBOX6 (MBOX_BLOCK+0xC)
! 372: #define OUTMAILBOX7 (MBOX_BLOCK+0xE)
! 373:
! 374: #define MBOX_OFF(n) (MBOX_BLOCK + ((n) << 1))
! 375: #define NMBOX(isp) \
! 376: (((((isp)->isp_type & ISP_HA_SCSI) >= ISP_HA_SCSI_1040A) || \
! 377: ((isp)->isp_type & ISP_HA_FC))? 8 : 6)
! 378: #define NMBOX_BMASK(isp) \
! 379: (((((isp)->isp_type & ISP_HA_SCSI) >= ISP_HA_SCSI_1040A) || \
! 380: ((isp)->isp_type & ISP_HA_FC))? 0xff : 0x3f)
! 381:
! 382: #define MAX_MAILBOX 8
! 383:
! 384: /*
! 385: * Fibre Protocol Module and Frame Buffer Register Offsets/Definitions (2X00).
! 386: * NB: The RISC processor must be paused and the appropriate register
! 387: * bank selected via BIU2100_CSR bits.
! 388: */
! 389:
! 390: #define FPM_DIAG_CONFIG (BIU_BLOCK + 0x96)
! 391: #define FPM_SOFT_RESET 0x0100
! 392:
! 393: #define FBM_CMD (BIU_BLOCK + 0xB8)
! 394: #define FBMCMD_FIFO_RESET_ALL 0xA000
! 395:
! 396:
! 397: /*
! 398: * SXP Block Register Offsets
! 399: */
! 400: #define SXP_PART_ID (SXP_BLOCK+0x0) /* R : Part ID Code */
! 401: #define SXP_CONFIG1 (SXP_BLOCK+0x2) /* RW*: Configuration Reg #1 */
! 402: #define SXP_CONFIG2 (SXP_BLOCK+0x4) /* RW*: Configuration Reg #2 */
! 403: #define SXP_CONFIG3 (SXP_BLOCK+0x6) /* RW*: Configuration Reg #2 */
! 404: #define SXP_INSTRUCTION (SXP_BLOCK+0xC) /* RW*: Instruction Pointer */
! 405: #define SXP_RETURN_ADDR (SXP_BLOCK+0x10) /* RW*: Return Address */
! 406: #define SXP_COMMAND (SXP_BLOCK+0x14) /* RW*: Command */
! 407: #define SXP_INTERRUPT (SXP_BLOCK+0x18) /* R : Interrupt */
! 408: #define SXP_SEQUENCE (SXP_BLOCK+0x1C) /* RW*: Sequence */
! 409: #define SXP_GROSS_ERR (SXP_BLOCK+0x1E) /* R : Gross Error */
! 410: #define SXP_EXCEPTION (SXP_BLOCK+0x20) /* RW*: Exception Enable */
! 411: #define SXP_OVERRIDE (SXP_BLOCK+0x24) /* RW*: Override */
! 412: #define SXP_LIT_BASE (SXP_BLOCK+0x28) /* RW*: Literal Base */
! 413: #define SXP_USER_FLAGS (SXP_BLOCK+0x2C) /* RW*: User Flags */
! 414: #define SXP_USER_EXCEPT (SXP_BLOCK+0x30) /* RW*: User Exception */
! 415: #define SXP_BREAKPOINT (SXP_BLOCK+0x34) /* RW*: Breakpoint */
! 416: #define SXP_SCSI_ID (SXP_BLOCK+0x40) /* RW*: SCSI ID */
! 417: #define SXP_DEV_CONFIG1 (SXP_BLOCK+0x42) /* RW*: Device Config Reg #1 */
! 418: #define SXP_DEV_CONFIG2 (SXP_BLOCK+0x44) /* RW*: Device Config Reg #2 */
! 419: #define SXP_PHASE_PTR (SXP_BLOCK+0x48) /* RW*: SCSI Phase Pointer */
! 420: #define SXP_BUF_PTR (SXP_BLOCK+0x4C) /* RW*: SCSI Buffer Pointer */
! 421: #define SXP_BUF_CTR (SXP_BLOCK+0x50) /* RW*: SCSI Buffer Counter */
! 422: #define SXP_BUFFER (SXP_BLOCK+0x52) /* RW*: SCSI Buffer */
! 423: #define SXP_BUF_BYTE (SXP_BLOCK+0x54) /* RW*: SCSI Buffer Byte */
! 424: #define SXP_BUF_WD (SXP_BLOCK+0x56) /* RW*: SCSI Buffer Word */
! 425: #define SXP_BUF_WD_TRAN (SXP_BLOCK+0x58) /* RW*: SCSI Buffer Wd xlate */
! 426: #define SXP_FIFO (SXP_BLOCK+0x5A) /* RW*: SCSI FIFO */
! 427: #define SXP_FIFO_STATUS (SXP_BLOCK+0x5C) /* RW*: SCSI FIFO Status */
! 428: #define SXP_FIFO_TOP (SXP_BLOCK+0x5E) /* RW*: SCSI FIFO Top Resid */
! 429: #define SXP_FIFO_BOTTOM (SXP_BLOCK+0x60) /* RW*: SCSI FIFO Bot Resid */
! 430: #define SXP_TRAN_REG (SXP_BLOCK+0x64) /* RW*: SCSI Transfer Reg */
! 431: #define SXP_TRAN_CNT_LO (SXP_BLOCK+0x68) /* RW*: SCSI Trans Count */
! 432: #define SXP_TRAN_CNT_HI (SXP_BLOCK+0x6A) /* RW*: SCSI Trans Count */
! 433: #define SXP_TRAN_CTR_LO (SXP_BLOCK+0x6C) /* RW*: SCSI Trans Counter */
! 434: #define SXP_TRAN_CTR_HI (SXP_BLOCK+0x6E) /* RW*: SCSI Trans Counter */
! 435: #define SXP_ARB_DATA (SXP_BLOCK+0x70) /* R : SCSI Arb Data */
! 436: #define SXP_PINS_CTRL (SXP_BLOCK+0x72) /* RW*: SCSI Control Pins */
! 437: #define SXP_PINS_DATA (SXP_BLOCK+0x74) /* RW*: SCSI Data Pins */
! 438: #define SXP_PINS_DIFF (SXP_BLOCK+0x76) /* RW*: SCSI Diff Pins */
! 439:
! 440: /* for 1080/1280/1240 only */
! 441: #define SXP_BANK1_SELECT 0x100
! 442:
! 443:
! 444: /* SXP CONF1 REGISTER */
! 445: #define SXP_CONF1_ASYNCH_SETUP 0xF000 /* Asynchronous setup time */
! 446: #define SXP_CONF1_SELECTION_UNIT 0x0000 /* Selection time unit */
! 447: #define SXP_CONF1_SELECTION_TIMEOUT 0x0600 /* Selection timeout */
! 448: #define SXP_CONF1_CLOCK_FACTOR 0x00E0 /* Clock factor */
! 449: #define SXP_CONF1_SCSI_ID 0x000F /* SCSI id */
! 450:
! 451: /* SXP CONF2 REGISTER */
! 452: #define SXP_CONF2_DISABLE_FILTER 0x0040 /* Disable SCSI rec filters */
! 453: #define SXP_CONF2_REQ_ACK_PULLUPS 0x0020 /* Enable req/ack pullups */
! 454: #define SXP_CONF2_DATA_PULLUPS 0x0010 /* Enable data pullups */
! 455: #define SXP_CONF2_CONFIG_AUTOLOAD 0x0008 /* Enable dev conf auto-load */
! 456: #define SXP_CONF2_RESELECT 0x0002 /* Enable reselection */
! 457: #define SXP_CONF2_SELECT 0x0001 /* Enable selection */
! 458:
! 459: /* SXP INTERRUPT REGISTER */
! 460: #define SXP_INT_PARITY_ERR 0x8000 /* Parity error detected */
! 461: #define SXP_INT_GROSS_ERR 0x4000 /* Gross error detected */
! 462: #define SXP_INT_FUNCTION_ABORT 0x2000 /* Last cmd aborted */
! 463: #define SXP_INT_CONDITION_FAILED 0x1000 /* Last cond failed test */
! 464: #define SXP_INT_FIFO_EMPTY 0x0800 /* SCSI FIFO is empty */
! 465: #define SXP_INT_BUF_COUNTER_ZERO 0x0400 /* SCSI buf count == zero */
! 466: #define SXP_INT_XFER_ZERO 0x0200 /* SCSI trans count == zero */
! 467: #define SXP_INT_INT_PENDING 0x0080 /* SXP interrupt pending */
! 468: #define SXP_INT_CMD_RUNNING 0x0040 /* SXP is running a command */
! 469: #define SXP_INT_INT_RETURN_CODE 0x000F /* Interrupt return code */
! 470:
! 471:
! 472: /* SXP GROSS ERROR REGISTER */
! 473: #define SXP_GROSS_OFFSET_RESID 0x0040 /* Req/Ack offset not zero */
! 474: #define SXP_GROSS_OFFSET_UNDERFLOW 0x0020 /* Req/Ack offset underflow */
! 475: #define SXP_GROSS_OFFSET_OVERFLOW 0x0010 /* Req/Ack offset overflow */
! 476: #define SXP_GROSS_FIFO_UNDERFLOW 0x0008 /* SCSI FIFO underflow */
! 477: #define SXP_GROSS_FIFO_OVERFLOW 0x0004 /* SCSI FIFO overflow */
! 478: #define SXP_GROSS_WRITE_ERR 0x0002 /* SXP and RISC wrote to reg */
! 479: #define SXP_GROSS_ILLEGAL_INST 0x0001 /* Bad inst loaded into SXP */
! 480:
! 481: /* SXP EXCEPTION REGISTER */
! 482: #define SXP_EXCEPT_USER_0 0x8000 /* Enable user exception #0 */
! 483: #define SXP_EXCEPT_USER_1 0x4000 /* Enable user exception #1 */
! 484: #define PCI_SXP_EXCEPT_SCAM 0x0400 /* SCAM Selection enable */
! 485: #define SXP_EXCEPT_BUS_FREE 0x0200 /* Enable Bus Free det */
! 486: #define SXP_EXCEPT_TARGET_ATN 0x0100 /* Enable TGT mode atten det */
! 487: #define SXP_EXCEPT_RESELECTED 0x0080 /* Enable ReSEL exc handling */
! 488: #define SXP_EXCEPT_SELECTED 0x0040 /* Enable SEL exc handling */
! 489: #define SXP_EXCEPT_ARBITRATION 0x0020 /* Enable ARB exc handling */
! 490: #define SXP_EXCEPT_GROSS_ERR 0x0010 /* Enable gross error except */
! 491: #define SXP_EXCEPT_BUS_RESET 0x0008 /* Enable Bus Reset except */
! 492:
! 493: /* SXP OVERRIDE REGISTER */
! 494: #define SXP_ORIDE_EXT_TRIGGER 0x8000 /* Enable external trigger */
! 495: #define SXP_ORIDE_STEP 0x4000 /* Enable single step mode */
! 496: #define SXP_ORIDE_BREAKPOINT 0x2000 /* Enable breakpoint reg */
! 497: #define SXP_ORIDE_PIN_WRITE 0x1000 /* Enable write to SCSI pins */
! 498: #define SXP_ORIDE_FORCE_OUTPUTS 0x0800 /* Force SCSI outputs on */
! 499: #define SXP_ORIDE_LOOPBACK 0x0400 /* Enable SCSI loopback mode */
! 500: #define SXP_ORIDE_PARITY_TEST 0x0200 /* Enable parity test mode */
! 501: #define SXP_ORIDE_TRISTATE_ENA_PINS 0x0100 /* Tristate SCSI enable pins */
! 502: #define SXP_ORIDE_TRISTATE_PINS 0x0080 /* Tristate SCSI pins */
! 503: #define SXP_ORIDE_FIFO_RESET 0x0008 /* Reset SCSI FIFO */
! 504: #define SXP_ORIDE_CMD_TERMINATE 0x0004 /* Terminate cur SXP com */
! 505: #define SXP_ORIDE_RESET_REG 0x0002 /* Reset SXP registers */
! 506: #define SXP_ORIDE_RESET_MODULE 0x0001 /* Reset SXP module */
! 507:
! 508: /* SXP COMMANDS */
! 509: #define SXP_RESET_BUS_CMD 0x300b
! 510:
! 511: /* SXP SCSI ID REGISTER */
! 512: #define SXP_SELECTING_ID 0x0F00 /* (Re)Selecting id */
! 513: #define SXP_SELECT_ID 0x000F /* Select id */
! 514:
! 515: /* SXP DEV CONFIG1 REGISTER */
! 516: #define SXP_DCONF1_SYNC_HOLD 0x7000 /* Synchronous data hold */
! 517: #define SXP_DCONF1_SYNC_SETUP 0x0F00 /* Synchronous data setup */
! 518: #define SXP_DCONF1_SYNC_OFFSET 0x000F /* Synchronous data offset */
! 519:
! 520:
! 521: /* SXP DEV CONFIG2 REGISTER */
! 522: #define SXP_DCONF2_FLAGS_MASK 0xF000 /* Device flags */
! 523: #define SXP_DCONF2_WIDE 0x0400 /* Enable wide SCSI */
! 524: #define SXP_DCONF2_PARITY 0x0200 /* Enable parity checking */
! 525: #define SXP_DCONF2_BLOCK_MODE 0x0100 /* Enable blk mode xfr count */
! 526: #define SXP_DCONF2_ASSERTION_MASK 0x0007 /* Assersion period mask */
! 527:
! 528:
! 529: /* SXP PHASE POINTER REGISTER */
! 530: #define SXP_PHASE_STATUS_PTR 0x1000 /* Status buffer offset */
! 531: #define SXP_PHASE_MSG_IN_PTR 0x0700 /* Msg in buffer offset */
! 532: #define SXP_PHASE_COM_PTR 0x00F0 /* Command buffer offset */
! 533: #define SXP_PHASE_MSG_OUT_PTR 0x0007 /* Msg out buffer offset */
! 534:
! 535:
! 536: /* SXP FIFO STATUS REGISTER */
! 537: #define SXP_FIFO_TOP_RESID 0x8000 /* Top residue reg full */
! 538: #define SXP_FIFO_ACK_RESID 0x4000 /* Wide transfers odd resid */
! 539: #define SXP_FIFO_COUNT_MASK 0x001C /* Words in SXP FIFO */
! 540: #define SXP_FIFO_BOTTOM_RESID 0x0001 /* Bottom residue reg full */
! 541:
! 542:
! 543: /* SXP CONTROL PINS REGISTER */
! 544: #define SXP_PINS_CON_PHASE 0x8000 /* Scsi phase valid */
! 545: #define SXP_PINS_CON_PARITY_HI 0x0400 /* Parity pin */
! 546: #define SXP_PINS_CON_PARITY_LO 0x0200 /* Parity pin */
! 547: #define SXP_PINS_CON_REQ 0x0100 /* SCSI bus REQUEST */
! 548: #define SXP_PINS_CON_ACK 0x0080 /* SCSI bus ACKNOWLEDGE */
! 549: #define SXP_PINS_CON_RST 0x0040 /* SCSI bus RESET */
! 550: #define SXP_PINS_CON_BSY 0x0020 /* SCSI bus BUSY */
! 551: #define SXP_PINS_CON_SEL 0x0010 /* SCSI bus SELECT */
! 552: #define SXP_PINS_CON_ATN 0x0008 /* SCSI bus ATTENTION */
! 553: #define SXP_PINS_CON_MSG 0x0004 /* SCSI bus MESSAGE */
! 554: #define SXP_PINS_CON_CD 0x0002 /* SCSI bus COMMAND */
! 555: #define SXP_PINS_CON_IO 0x0001 /* SCSI bus INPUT */
! 556:
! 557: /*
! 558: * Set the hold time for the SCSI Bus Reset to be 250 ms
! 559: */
! 560: #define SXP_SCSI_BUS_RESET_HOLD_TIME 250
! 561:
! 562: /* SXP DIFF PINS REGISTER */
! 563: #define SXP_PINS_DIFF_SENSE 0x0200 /* DIFFSENS sig on SCSI bus */
! 564: #define SXP_PINS_DIFF_MODE 0x0100 /* DIFFM signal */
! 565: #define SXP_PINS_DIFF_ENABLE_OUTPUT 0x0080 /* Enable SXP SCSI data drv */
! 566: #define SXP_PINS_DIFF_PINS_MASK 0x007C /* Differential control pins */
! 567: #define SXP_PINS_DIFF_TARGET 0x0002 /* Enable SXP target mode */
! 568: #define SXP_PINS_DIFF_INITIATOR 0x0001 /* Enable SXP initiator mode */
! 569:
! 570: /* Ultra2 only */
! 571: #define SXP_PINS_LVD_MODE 0x1000
! 572: #define SXP_PINS_HVD_MODE 0x0800
! 573: #define SXP_PINS_SE_MODE 0x0400
! 574:
! 575: /* The above have to be put together with the DIFFM pin to make sense */
! 576: #define ISP1080_LVD_MODE (SXP_PINS_LVD_MODE)
! 577: #define ISP1080_HVD_MODE (SXP_PINS_HVD_MODE|SXP_PINS_DIFF_MODE)
! 578: #define ISP1080_SE_MODE (SXP_PINS_SE_MODE)
! 579: #define ISP1080_MODE_MASK \
! 580: (SXP_PINS_LVD_MODE|SXP_PINS_HVD_MODE|SXP_PINS_SE_MODE|SXP_PINS_DIFF_MODE)
! 581:
! 582: /*
! 583: * RISC and Host Command and Control Block Register Offsets
! 584: */
! 585:
! 586: #define RISC_ACC RISC_BLOCK+0x0 /* RW*: Accumulator */
! 587: #define RISC_R1 RISC_BLOCK+0x2 /* RW*: GP Reg R1 */
! 588: #define RISC_R2 RISC_BLOCK+0x4 /* RW*: GP Reg R2 */
! 589: #define RISC_R3 RISC_BLOCK+0x6 /* RW*: GP Reg R3 */
! 590: #define RISC_R4 RISC_BLOCK+0x8 /* RW*: GP Reg R4 */
! 591: #define RISC_R5 RISC_BLOCK+0xA /* RW*: GP Reg R5 */
! 592: #define RISC_R6 RISC_BLOCK+0xC /* RW*: GP Reg R6 */
! 593: #define RISC_R7 RISC_BLOCK+0xE /* RW*: GP Reg R7 */
! 594: #define RISC_R8 RISC_BLOCK+0x10 /* RW*: GP Reg R8 */
! 595: #define RISC_R9 RISC_BLOCK+0x12 /* RW*: GP Reg R9 */
! 596: #define RISC_R10 RISC_BLOCK+0x14 /* RW*: GP Reg R10 */
! 597: #define RISC_R11 RISC_BLOCK+0x16 /* RW*: GP Reg R11 */
! 598: #define RISC_R12 RISC_BLOCK+0x18 /* RW*: GP Reg R12 */
! 599: #define RISC_R13 RISC_BLOCK+0x1a /* RW*: GP Reg R13 */
! 600: #define RISC_R14 RISC_BLOCK+0x1c /* RW*: GP Reg R14 */
! 601: #define RISC_R15 RISC_BLOCK+0x1e /* RW*: GP Reg R15 */
! 602: #define RISC_PSR RISC_BLOCK+0x20 /* RW*: Processor Status */
! 603: #define RISC_IVR RISC_BLOCK+0x22 /* RW*: Interrupt Vector */
! 604: #define RISC_PCR RISC_BLOCK+0x24 /* RW*: Processor Ctrl */
! 605: #define RISC_RAR0 RISC_BLOCK+0x26 /* RW*: Ram Address #0 */
! 606: #define RISC_RAR1 RISC_BLOCK+0x28 /* RW*: Ram Address #1 */
! 607: #define RISC_LCR RISC_BLOCK+0x2a /* RW*: Loop Counter */
! 608: #define RISC_PC RISC_BLOCK+0x2c /* R : Program Counter */
! 609: #define RISC_MTR RISC_BLOCK+0x2e /* RW*: Memory Timing */
! 610: #define RISC_MTR2100 RISC_BLOCK+0x30
! 611:
! 612: #define RISC_EMB RISC_BLOCK+0x30 /* RW*: Ext Mem Boundary */
! 613: #define DUAL_BANK 8
! 614: #define RISC_SP RISC_BLOCK+0x32 /* RW*: Stack Pointer */
! 615: #define RISC_HRL RISC_BLOCK+0x3e /* R *: Hardware Rev Level */
! 616: #define HCCR RISC_BLOCK+0x40 /* RW : Host Command & Ctrl */
! 617: #define BP0 RISC_BLOCK+0x42 /* RW : Processor Brkpt #0 */
! 618: #define BP1 RISC_BLOCK+0x44 /* RW : Processor Brkpt #1 */
! 619: #define TCR RISC_BLOCK+0x46 /* W : Test Control */
! 620: #define TMR RISC_BLOCK+0x48 /* W : Test Mode */
! 621:
! 622:
! 623: /* PROCESSOR STATUS REGISTER */
! 624: #define RISC_PSR_FORCE_TRUE 0x8000
! 625: #define RISC_PSR_LOOP_COUNT_DONE 0x4000
! 626: #define RISC_PSR_RISC_INT 0x2000
! 627: #define RISC_PSR_TIMER_ROLLOVER 0x1000
! 628: #define RISC_PSR_ALU_OVERFLOW 0x0800
! 629: #define RISC_PSR_ALU_MSB 0x0400
! 630: #define RISC_PSR_ALU_CARRY 0x0200
! 631: #define RISC_PSR_ALU_ZERO 0x0100
! 632:
! 633: #define RISC_PSR_PCI_ULTRA 0x0080
! 634: #define RISC_PSR_SBUS_ULTRA 0x0020
! 635:
! 636: #define RISC_PSR_DMA_INT 0x0010
! 637: #define RISC_PSR_SXP_INT 0x0008
! 638: #define RISC_PSR_HOST_INT 0x0004
! 639: #define RISC_PSR_INT_PENDING 0x0002
! 640: #define RISC_PSR_FORCE_FALSE 0x0001
! 641:
! 642:
! 643: /* Host Command and Control */
! 644: #define HCCR_CMD_NOP 0x0000 /* NOP */
! 645: #define HCCR_CMD_RESET 0x1000 /* Reset RISC */
! 646: #define HCCR_CMD_PAUSE 0x2000 /* Pause RISC */
! 647: #define HCCR_CMD_RELEASE 0x3000 /* Release Paused RISC */
! 648: #define HCCR_CMD_STEP 0x4000 /* Single Step RISC */
! 649: #define HCCR_2X00_DISABLE_PARITY_PAUSE 0x4001 /*
! 650: * Disable RISC pause on FPM
! 651: * parity error.
! 652: */
! 653: #define HCCR_CMD_SET_HOST_INT 0x5000 /* Set Host Interrupt */
! 654: #define HCCR_CMD_CLEAR_HOST_INT 0x6000 /* Clear Host Interrupt */
! 655: #define HCCR_CMD_CLEAR_RISC_INT 0x7000 /* Clear RISC interrupt */
! 656: #define HCCR_CMD_BREAKPOINT 0x8000 /* Change breakpoint enables */
! 657: #define PCI_HCCR_CMD_BIOS 0x9000 /* Write BIOS (disable) */
! 658: #define PCI_HCCR_CMD_PARITY 0xA000 /* Write parity enable */
! 659: #define PCI_HCCR_CMD_PARITY_ERR 0xE000 /* Generate parity error */
! 660: #define HCCR_CMD_TEST_MODE 0xF000 /* Set Test Mode */
! 661:
! 662: #define ISP2100_HCCR_PARITY_ENABLE_2 0x0400
! 663: #define ISP2100_HCCR_PARITY_ENABLE_1 0x0200
! 664: #define ISP2100_HCCR_PARITY_ENABLE_0 0x0100
! 665: #define ISP2100_HCCR_PARITY 0x0001
! 666:
! 667: #define PCI_HCCR_PARITY 0x0400 /* Parity error flag */
! 668: #define PCI_HCCR_PARITY_ENABLE_1 0x0200 /* Parity enable bank 1 */
! 669: #define PCI_HCCR_PARITY_ENABLE_0 0x0100 /* Parity enable bank 0 */
! 670:
! 671: #define HCCR_HOST_INT 0x0080 /* R : Host interrupt set */
! 672: #define HCCR_RESET 0x0040 /* R : reset in progress */
! 673: #define HCCR_PAUSE 0x0020 /* R : RISC paused */
! 674:
! 675: #define PCI_HCCR_BIOS 0x0001 /* W : BIOS enable */
! 676:
! 677: /*
! 678: * NVRAM Definitions (PCI cards only)
! 679: */
! 680:
! 681: #define ISPBSMX(c, byte, shift, mask) \
! 682: (((c)[(byte)] >> (shift)) & (mask))
! 683: /*
! 684: * Qlogic 1020/1040 NVRAM is an array of 128 bytes.
! 685: *
! 686: * Some portion of the front of this is for general host adapter properties
! 687: * This is followed by an array of per-target parameters, and is tailed off
! 688: * with a checksum xor byte at offset 127. For non-byte entities data is
! 689: * stored in Little Endian order.
! 690: */
! 691:
! 692: #define ISP_NVRAM_SIZE 128
! 693:
! 694: #define ISP_NVRAM_VERSION(c) (c)[4]
! 695: #define ISP_NVRAM_FIFO_THRESHOLD(c) ISPBSMX(c, 5, 0, 0x03)
! 696: #define ISP_NVRAM_BIOS_DISABLE(c) ISPBSMX(c, 5, 2, 0x01)
! 697: #define ISP_NVRAM_HBA_ENABLE(c) ISPBSMX(c, 5, 3, 0x01)
! 698: #define ISP_NVRAM_INITIATOR_ID(c) ISPBSMX(c, 5, 4, 0x0f)
! 699: #define ISP_NVRAM_BUS_RESET_DELAY(c) (c)[6]
! 700: #define ISP_NVRAM_BUS_RETRY_COUNT(c) (c)[7]
! 701: #define ISP_NVRAM_BUS_RETRY_DELAY(c) (c)[8]
! 702: #define ISP_NVRAM_ASYNC_DATA_SETUP_TIME(c) ISPBSMX(c, 9, 0, 0x0f)
! 703: #define ISP_NVRAM_REQ_ACK_ACTIVE_NEGATION(c) ISPBSMX(c, 9, 4, 0x01)
! 704: #define ISP_NVRAM_DATA_LINE_ACTIVE_NEGATION(c) ISPBSMX(c, 9, 5, 0x01)
! 705: #define ISP_NVRAM_DATA_DMA_BURST_ENABLE(c) ISPBSMX(c, 9, 6, 0x01)
! 706: #define ISP_NVRAM_CMD_DMA_BURST_ENABLE(c) ISPBSMX(c, 9, 7, 0x01)
! 707: #define ISP_NVRAM_TAG_AGE_LIMIT(c) (c)[10]
! 708: #define ISP_NVRAM_LOWTRM_ENABLE(c) ISPBSMX(c, 11, 0, 0x01)
! 709: #define ISP_NVRAM_HITRM_ENABLE(c) ISPBSMX(c, 11, 1, 0x01)
! 710: #define ISP_NVRAM_PCMC_BURST_ENABLE(c) ISPBSMX(c, 11, 2, 0x01)
! 711: #define ISP_NVRAM_ENABLE_60_MHZ(c) ISPBSMX(c, 11, 3, 0x01)
! 712: #define ISP_NVRAM_SCSI_RESET_DISABLE(c) ISPBSMX(c, 11, 4, 0x01)
! 713: #define ISP_NVRAM_ENABLE_AUTO_TERM(c) ISPBSMX(c, 11, 5, 0x01)
! 714: #define ISP_NVRAM_FIFO_THRESHOLD_128(c) ISPBSMX(c, 11, 6, 0x01)
! 715: #define ISP_NVRAM_AUTO_TERM_SUPPORT(c) ISPBSMX(c, 11, 7, 0x01)
! 716: #define ISP_NVRAM_SELECTION_TIMEOUT(c) (((c)[12]) | ((c)[13] << 8))
! 717: #define ISP_NVRAM_MAX_QUEUE_DEPTH(c) (((c)[14]) | ((c)[15] << 8))
! 718: #define ISP_NVRAM_SCSI_BUS_SIZE(c) ISPBSMX(c, 16, 0, 0x01)
! 719: #define ISP_NVRAM_SCSI_BUS_TYPE(c) ISPBSMX(c, 16, 1, 0x01)
! 720: #define ISP_NVRAM_ADAPTER_CLK_SPEED(c) ISPBSMX(c, 16, 2, 0x01)
! 721: #define ISP_NVRAM_SOFT_TERM_SUPPORT(c) ISPBSMX(c, 16, 3, 0x01)
! 722: #define ISP_NVRAM_FLASH_ONBOARD(c) ISPBSMX(c, 16, 4, 0x01)
! 723: #define ISP_NVRAM_FAST_MTTR_ENABLE(c) ISPBSMX(c, 22, 0, 0x01)
! 724:
! 725: #define ISP_NVRAM_TARGOFF 28
! 726: #define ISP_NVARM_TARGSIZE 6
! 727: #define _IxT(tgt, tidx) \
! 728: (ISP_NVRAM_TARGOFF + (ISP_NVARM_TARGSIZE * (tgt)) + (tidx))
! 729: #define ISP_NVRAM_TGT_RENEG(c, t) ISPBSMX(c, _IxT(t, 0), 0, 0x01)
! 730: #define ISP_NVRAM_TGT_QFRZ(c, t) ISPBSMX(c, _IxT(t, 0), 1, 0x01)
! 731: #define ISP_NVRAM_TGT_ARQ(c, t) ISPBSMX(c, _IxT(t, 0), 2, 0x01)
! 732: #define ISP_NVRAM_TGT_TQING(c, t) ISPBSMX(c, _IxT(t, 0), 3, 0x01)
! 733: #define ISP_NVRAM_TGT_SYNC(c, t) ISPBSMX(c, _IxT(t, 0), 4, 0x01)
! 734: #define ISP_NVRAM_TGT_WIDE(c, t) ISPBSMX(c, _IxT(t, 0), 5, 0x01)
! 735: #define ISP_NVRAM_TGT_PARITY(c, t) ISPBSMX(c, _IxT(t, 0), 6, 0x01)
! 736: #define ISP_NVRAM_TGT_DISC(c, t) ISPBSMX(c, _IxT(t, 0), 7, 0x01)
! 737: #define ISP_NVRAM_TGT_EXEC_THROTTLE(c, t) ISPBSMX(c, _IxT(t, 1), 0, 0xff)
! 738: #define ISP_NVRAM_TGT_SYNC_PERIOD(c, t) ISPBSMX(c, _IxT(t, 2), 0, 0xff)
! 739: #define ISP_NVRAM_TGT_SYNC_OFFSET(c, t) ISPBSMX(c, _IxT(t, 3), 0, 0x0f)
! 740: #define ISP_NVRAM_TGT_DEVICE_ENABLE(c, t) ISPBSMX(c, _IxT(t, 3), 4, 0x01)
! 741: #define ISP_NVRAM_TGT_LUN_DISABLE(c, t) ISPBSMX(c, _IxT(t, 3), 5, 0x01)
! 742:
! 743: /*
! 744: * Qlogic 1080/1240 NVRAM is an array of 256 bytes.
! 745: *
! 746: * Some portion of the front of this is for general host adapter properties
! 747: * This is followed by an array of per-target parameters, and is tailed off
! 748: * with a checksum xor byte at offset 256. For non-byte entities data is
! 749: * stored in Little Endian order.
! 750: */
! 751:
! 752: #define ISP1080_NVRAM_SIZE 256
! 753:
! 754: #define ISP1080_NVRAM_VERSION(c) ISP_NVRAM_VERSION(c)
! 755:
! 756: /* Offset 5 */
! 757: /*
! 758: u_int8_t bios_configuration_mode :2;
! 759: u_int8_t bios_disable :1;
! 760: u_int8_t selectable_scsi_boot_enable :1;
! 761: u_int8_t cd_rom_boot_enable :1;
! 762: u_int8_t disable_loading_risc_code :1;
! 763: u_int8_t enable_64bit_addressing :1;
! 764: u_int8_t unused_7 :1;
! 765: */
! 766:
! 767: /* Offsets 6, 7 */
! 768: /*
! 769: u_int8_t boot_lun_number :5;
! 770: u_int8_t scsi_bus_number :1;
! 771: u_int8_t unused_6 :1;
! 772: u_int8_t unused_7 :1;
! 773: u_int8_t boot_target_number :4;
! 774: u_int8_t unused_12 :1;
! 775: u_int8_t unused_13 :1;
! 776: u_int8_t unused_14 :1;
! 777: u_int8_t unused_15 :1;
! 778: */
! 779:
! 780: #define ISP1080_NVRAM_HBA_ENABLE(c) ISPBSMX(c, 16, 3, 0x01)
! 781:
! 782: #define ISP1080_NVRAM_BURST_ENABLE(c) ISPBSMX(c, 16, 1, 0x01)
! 783: #define ISP1080_NVRAM_FIFO_THRESHOLD(c) ISPBSMX(c, 16, 4, 0x0f)
! 784:
! 785: #define ISP1080_NVRAM_AUTO_TERM_SUPPORT(c) ISPBSMX(c, 17, 7, 0x01)
! 786: #define ISP1080_NVRAM_BUS0_TERM_MODE(c) ISPBSMX(c, 17, 0, 0x03)
! 787: #define ISP1080_NVRAM_BUS1_TERM_MODE(c) ISPBSMX(c, 17, 2, 0x03)
! 788:
! 789: #define ISP1080_ISP_PARAMETER(c) \
! 790: (((c)[18]) | ((c)[19] << 8))
! 791:
! 792: #define ISP1080_FAST_POST(c) ISPBSMX(c, 20, 0, 0x01)
! 793: #define ISP1080_REPORT_LVD_TRANSITION(c) ISPBSMX(c, 20, 1, 0x01)
! 794:
! 795: #define ISP1080_BUS1_OFF 112
! 796:
! 797: #define ISP1080_NVRAM_INITIATOR_ID(c, b) \
! 798: ISPBSMX(c, ((b == 0)? 0 : ISP1080_BUS1_OFF) + 24, 0, 0x0f)
! 799: #define ISP1080_NVRAM_BUS_RESET_DELAY(c, b) \
! 800: (c)[((b == 0)? 0 : ISP1080_BUS1_OFF) + 25]
! 801: #define ISP1080_NVRAM_BUS_RETRY_COUNT(c, b) \
! 802: (c)[((b == 0)? 0 : ISP1080_BUS1_OFF) + 26]
! 803: #define ISP1080_NVRAM_BUS_RETRY_DELAY(c, b) \
! 804: (c)[((b == 0)? 0 : ISP1080_BUS1_OFF) + 27]
! 805:
! 806: #define ISP1080_NVRAM_ASYNC_DATA_SETUP_TIME(c, b) \
! 807: ISPBSMX(c, ((b == 0)? 0 : ISP1080_BUS1_OFF) + 28, 0, 0x0f)
! 808: #define ISP1080_NVRAM_REQ_ACK_ACTIVE_NEGATION(c, b) \
! 809: ISPBSMX(c, ((b == 0)? 0 : ISP1080_BUS1_OFF) + 28, 4, 0x01)
! 810: #define ISP1080_NVRAM_DATA_LINE_ACTIVE_NEGATION(c, b) \
! 811: ISPBSMX(c, ((b == 0)? 0 : ISP1080_BUS1_OFF) + 28, 5, 0x01)
! 812: #define ISP1080_NVRAM_SELECTION_TIMEOUT(c, b) \
! 813: (((c)[((b == 0)? 0 : ISP1080_BUS1_OFF) + 30]) | \
! 814: ((c)[((b == 0)? 0 : ISP1080_BUS1_OFF) + 31] << 8))
! 815: #define ISP1080_NVRAM_MAX_QUEUE_DEPTH(c, b) \
! 816: (((c)[((b == 0)? 0 : ISP1080_BUS1_OFF) + 32]) | \
! 817: ((c)[((b == 0)? 0 : ISP1080_BUS1_OFF) + 33] << 8))
! 818:
! 819: #define ISP1080_NVRAM_TARGOFF(b) \
! 820: ((b == 0)? 40: (40 + ISP1080_BUS1_OFF))
! 821: #define ISP1080_NVRAM_TARGSIZE 6
! 822: #define _IxT8(tgt, tidx, b) \
! 823: (ISP1080_NVRAM_TARGOFF((b)) + (ISP1080_NVRAM_TARGSIZE * (tgt)) + (tidx))
! 824:
! 825: #define ISP1080_NVRAM_TGT_RENEG(c, t, b) \
! 826: ISPBSMX(c, _IxT8(t, 0, (b)), 0, 0x01)
! 827: #define ISP1080_NVRAM_TGT_QFRZ(c, t, b) \
! 828: ISPBSMX(c, _IxT8(t, 0, (b)), 1, 0x01)
! 829: #define ISP1080_NVRAM_TGT_ARQ(c, t, b) \
! 830: ISPBSMX(c, _IxT8(t, 0, (b)), 2, 0x01)
! 831: #define ISP1080_NVRAM_TGT_TQING(c, t, b) \
! 832: ISPBSMX(c, _IxT8(t, 0, (b)), 3, 0x01)
! 833: #define ISP1080_NVRAM_TGT_SYNC(c, t, b) \
! 834: ISPBSMX(c, _IxT8(t, 0, (b)), 4, 0x01)
! 835: #define ISP1080_NVRAM_TGT_WIDE(c, t, b) \
! 836: ISPBSMX(c, _IxT8(t, 0, (b)), 5, 0x01)
! 837: #define ISP1080_NVRAM_TGT_PARITY(c, t, b) \
! 838: ISPBSMX(c, _IxT8(t, 0, (b)), 6, 0x01)
! 839: #define ISP1080_NVRAM_TGT_DISC(c, t, b) \
! 840: ISPBSMX(c, _IxT8(t, 0, (b)), 7, 0x01)
! 841: #define ISP1080_NVRAM_TGT_EXEC_THROTTLE(c, t, b) \
! 842: ISPBSMX(c, _IxT8(t, 1, (b)), 0, 0xff)
! 843: #define ISP1080_NVRAM_TGT_SYNC_PERIOD(c, t, b) \
! 844: ISPBSMX(c, _IxT8(t, 2, (b)), 0, 0xff)
! 845: #define ISP1080_NVRAM_TGT_SYNC_OFFSET(c, t, b) \
! 846: ISPBSMX(c, _IxT8(t, 3, (b)), 0, 0x0f)
! 847: #define ISP1080_NVRAM_TGT_DEVICE_ENABLE(c, t, b) \
! 848: ISPBSMX(c, _IxT8(t, 3, (b)), 4, 0x01)
! 849: #define ISP1080_NVRAM_TGT_LUN_DISABLE(c, t, b) \
! 850: ISPBSMX(c, _IxT8(t, 3, (b)), 5, 0x01)
! 851:
! 852: #define ISP12160_NVRAM_HBA_ENABLE ISP1080_NVRAM_HBA_ENABLE
! 853: #define ISP12160_NVRAM_BURST_ENABLE ISP1080_NVRAM_BURST_ENABLE
! 854: #define ISP12160_NVRAM_FIFO_THRESHOLD ISP1080_NVRAM_FIFO_THRESHOLD
! 855: #define ISP12160_NVRAM_AUTO_TERM_SUPPORT ISP1080_NVRAM_AUTO_TERM_SUPPORT
! 856: #define ISP12160_NVRAM_BUS0_TERM_MODE ISP1080_NVRAM_BUS0_TERM_MODE
! 857: #define ISP12160_NVRAM_BUS1_TERM_MODE ISP1080_NVRAM_BUS1_TERM_MODE
! 858: #define ISP12160_ISP_PARAMETER ISP12160_ISP_PARAMETER
! 859: #define ISP12160_FAST_POST ISP1080_FAST_POST
! 860: #define ISP12160_REPORT_LVD_TRANSITION ISP1080_REPORT_LVD_TRANSTION
! 861:
! 862: #define ISP12160_NVRAM_INITIATOR_ID \
! 863: ISP1080_NVRAM_INITIATOR_ID
! 864: #define ISP12160_NVRAM_BUS_RESET_DELAY \
! 865: ISP1080_NVRAM_BUS_RESET_DELAY
! 866: #define ISP12160_NVRAM_BUS_RETRY_COUNT \
! 867: ISP1080_NVRAM_BUS_RETRY_COUNT
! 868: #define ISP12160_NVRAM_BUS_RETRY_DELAY \
! 869: ISP1080_NVRAM_BUS_RETRY_DELAY
! 870: #define ISP12160_NVRAM_ASYNC_DATA_SETUP_TIME \
! 871: ISP1080_NVRAM_ASYNC_DATA_SETUP_TIME
! 872: #define ISP12160_NVRAM_REQ_ACK_ACTIVE_NEGATION \
! 873: ISP1080_NVRAM_REQ_ACK_ACTIVE_NEGATION
! 874: #define ISP12160_NVRAM_DATA_LINE_ACTIVE_NEGATION \
! 875: ISP1080_NVRAM_DATA_LINE_ACTIVE_NEGATION
! 876: #define ISP12160_NVRAM_SELECTION_TIMEOUT \
! 877: ISP1080_NVRAM_SELECTION_TIMEOUT
! 878: #define ISP12160_NVRAM_MAX_QUEUE_DEPTH \
! 879: ISP1080_NVRAM_MAX_QUEUE_DEPTH
! 880:
! 881:
! 882: #define ISP12160_BUS0_OFF 24
! 883: #define ISP12160_BUS1_OFF 136
! 884:
! 885: #define ISP12160_NVRAM_TARGOFF(b) \
! 886: (((b == 0)? ISP12160_BUS0_OFF : ISP12160_BUS1_OFF) + 16)
! 887:
! 888: #define ISP12160_NVRAM_TARGSIZE 6
! 889: #define _IxT16(tgt, tidx, b) \
! 890: (ISP12160_NVRAM_TARGOFF((b))+(ISP12160_NVRAM_TARGSIZE * (tgt))+(tidx))
! 891:
! 892: #define ISP12160_NVRAM_TGT_RENEG(c, t, b) \
! 893: ISPBSMX(c, _IxT16(t, 0, (b)), 0, 0x01)
! 894: #define ISP12160_NVRAM_TGT_QFRZ(c, t, b) \
! 895: ISPBSMX(c, _IxT16(t, 0, (b)), 1, 0x01)
! 896: #define ISP12160_NVRAM_TGT_ARQ(c, t, b) \
! 897: ISPBSMX(c, _IxT16(t, 0, (b)), 2, 0x01)
! 898: #define ISP12160_NVRAM_TGT_TQING(c, t, b) \
! 899: ISPBSMX(c, _IxT16(t, 0, (b)), 3, 0x01)
! 900: #define ISP12160_NVRAM_TGT_SYNC(c, t, b) \
! 901: ISPBSMX(c, _IxT16(t, 0, (b)), 4, 0x01)
! 902: #define ISP12160_NVRAM_TGT_WIDE(c, t, b) \
! 903: ISPBSMX(c, _IxT16(t, 0, (b)), 5, 0x01)
! 904: #define ISP12160_NVRAM_TGT_PARITY(c, t, b) \
! 905: ISPBSMX(c, _IxT16(t, 0, (b)), 6, 0x01)
! 906: #define ISP12160_NVRAM_TGT_DISC(c, t, b) \
! 907: ISPBSMX(c, _IxT16(t, 0, (b)), 7, 0x01)
! 908:
! 909: #define ISP12160_NVRAM_TGT_EXEC_THROTTLE(c, t, b) \
! 910: ISPBSMX(c, _IxT16(t, 1, (b)), 0, 0xff)
! 911: #define ISP12160_NVRAM_TGT_SYNC_PERIOD(c, t, b) \
! 912: ISPBSMX(c, _IxT16(t, 2, (b)), 0, 0xff)
! 913:
! 914: #define ISP12160_NVRAM_TGT_SYNC_OFFSET(c, t, b) \
! 915: ISPBSMX(c, _IxT16(t, 3, (b)), 0, 0x1f)
! 916: #define ISP12160_NVRAM_TGT_DEVICE_ENABLE(c, t, b) \
! 917: ISPBSMX(c, _IxT16(t, 3, (b)), 5, 0x01)
! 918:
! 919: #define ISP12160_NVRAM_PPR_OPTIONS(c, t, b) \
! 920: ISPBSMX(c, _IxT16(t, 4, (b)), 0, 0x0f)
! 921: #define ISP12160_NVRAM_PPR_WIDTH(c, t, b) \
! 922: ISPBSMX(c, _IxT16(t, 4, (b)), 4, 0x03)
! 923: #define ISP12160_NVRAM_PPR_ENABLE(c, t, b) \
! 924: ISPBSMX(c, _IxT16(t, 4, (b)), 7, 0x01)
! 925:
! 926: /*
! 927: * Qlogic 2XXX NVRAM is an array of 256 bytes.
! 928: *
! 929: * Some portion of the front of this is for general RISC engine parameters,
! 930: * mostly reflecting the state of the last INITIALIZE FIRMWARE mailbox command.
! 931: *
! 932: * This is followed by some general host adapter parameters, and ends with
! 933: * a checksum xor byte at offset 255. For non-byte entities data is stored
! 934: * in Little Endian order.
! 935: */
! 936: #define ISP2100_NVRAM_SIZE 256
! 937: /* ISP_NVRAM_VERSION is in same overall place */
! 938: #define ISP2100_NVRAM_RISCVER(c) (c)[6]
! 939: #define ISP2100_NVRAM_OPTIONS(c) (c)[8]
! 940: #define ISP2100_NVRAM_MAXFRAMELENGTH(c) (((c)[10]) | ((c)[11] << 8))
! 941: #define ISP2100_NVRAM_MAXIOCBALLOCATION(c) (((c)[12]) | ((c)[13] << 8))
! 942: #define ISP2100_NVRAM_EXECUTION_THROTTLE(c) (((c)[14]) | ((c)[15] << 8))
! 943: #define ISP2100_NVRAM_RETRY_COUNT(c) (c)[16]
! 944: #define ISP2100_NVRAM_RETRY_DELAY(c) (c)[17]
! 945:
! 946: #define ISP2100_NVRAM_PORT_NAME(c) (\
! 947: (((u_int64_t)(c)[18]) << 56) | \
! 948: (((u_int64_t)(c)[19]) << 48) | \
! 949: (((u_int64_t)(c)[20]) << 40) | \
! 950: (((u_int64_t)(c)[21]) << 32) | \
! 951: (((u_int64_t)(c)[22]) << 24) | \
! 952: (((u_int64_t)(c)[23]) << 16) | \
! 953: (((u_int64_t)(c)[24]) << 8) | \
! 954: (((u_int64_t)(c)[25]) << 0))
! 955:
! 956: #define ISP2100_NVRAM_HARDLOOPID(c) (c)[26]
! 957:
! 958: #define ISP2200_NVRAM_NODE_NAME(c) (\
! 959: (((u_int64_t)(c)[30]) << 56) | \
! 960: (((u_int64_t)(c)[31]) << 48) | \
! 961: (((u_int64_t)(c)[32]) << 40) | \
! 962: (((u_int64_t)(c)[33]) << 32) | \
! 963: (((u_int64_t)(c)[34]) << 24) | \
! 964: (((u_int64_t)(c)[35]) << 16) | \
! 965: (((u_int64_t)(c)[36]) << 8) | \
! 966: (((u_int64_t)(c)[37]) << 0))
! 967:
! 968: #define ISP2100_NVRAM_HBA_OPTIONS(c) (c)[70]
! 969: #define ISP2100_NVRAM_HBA_DISABLE(c) ISPBSMX(c, 70, 0, 0x01)
! 970: #define ISP2100_NVRAM_BIOS_DISABLE(c) ISPBSMX(c, 70, 1, 0x01)
! 971: #define ISP2100_NVRAM_LUN_DISABLE(c) ISPBSMX(c, 70, 2, 0x01)
! 972: #define ISP2100_NVRAM_ENABLE_SELECT_BOOT(c) ISPBSMX(c, 70, 3, 0x01)
! 973: #define ISP2100_NVRAM_DISABLE_CODELOAD(c) ISPBSMX(c, 70, 4, 0x01)
! 974: #define ISP2100_NVRAM_SET_CACHELINESZ(c) ISPBSMX(c, 70, 5, 0x01)
! 975:
! 976: #define ISP2100_NVRAM_BOOT_NODE_NAME(c) (\
! 977: (((u_int64_t)(c)[72]) << 56) | \
! 978: (((u_int64_t)(c)[73]) << 48) | \
! 979: (((u_int64_t)(c)[74]) << 40) | \
! 980: (((u_int64_t)(c)[75]) << 32) | \
! 981: (((u_int64_t)(c)[76]) << 24) | \
! 982: (((u_int64_t)(c)[77]) << 16) | \
! 983: (((u_int64_t)(c)[78]) << 8) | \
! 984: (((u_int64_t)(c)[79]) << 0))
! 985:
! 986: #define ISP2100_NVRAM_BOOT_LUN(c) (c)[80]
! 987:
! 988: #define ISP2200_HBA_FEATURES(c) (c)[232] | ((c)[233] << 8)
! 989:
! 990: /*
! 991: * Firmware Crash Dump
! 992: *
! 993: * QLogic needs specific information format when they look at firmware crashes.
! 994: *
! 995: * This is incredibly kernel memory consumptive (to say the least), so this
! 996: * code is only compiled in when needed.
! 997: */
! 998:
! 999: #define QLA2200_RISC_IMAGE_DUMP_SIZE \
! 1000: (1 * sizeof (u_int16_t)) + /* 'used' flag (also HBA type) */ \
! 1001: (352 * sizeof (u_int16_t)) + /* RISC registers */ \
! 1002: (61440 * sizeof (u_int16_t)) /* RISC SRAM (offset 0x1000..0xffff) */
! 1003: #define QLA2300_RISC_IMAGE_DUMP_SIZE \
! 1004: (1 * sizeof (u_int16_t)) + /* 'used' flag (also HBA type) */ \
! 1005: (464 * sizeof (u_int16_t)) + /* RISC registers */ \
! 1006: (63488 * sizeof (u_int16_t)) + /* RISC SRAM (0x0800..0xffff) */ \
! 1007: (4096 * sizeof (u_int16_t)) + /* RISC SRAM (0x10000..0x10FFF) */ \
! 1008: (61440 * sizeof (u_int16_t)) /* RISC SRAM (0x11000..0x1FFFF) */
! 1009: /* the larger of the two */
! 1010: #define ISP_CRASH_IMAGE_SIZE QLA2300_RISC_IMAGE_DUMP_SIZE
! 1011: #endif /* _ISPREG_H */
CVSweb