Annotation of sys/dev/ic/iha.h, Revision 1.1.1.1
1.1 nbrk 1: /* $OpenBSD: iha.h,v 1.15 2004/01/19 00:44:33 krw Exp $ */
2: /*-------------------------------------------------------------------------
3: *
4: * Device driver for the INI-9XXXU/UW or INIC-940/950 PCI SCSI Controller.
5: *
6: * Written for 386bsd and FreeBSD by
7: * Winston Hung <winstonh@initio.com>
8: *
9: * Copyright (c) 1997-1999 Initio Corp
10: * Copyright (c) 2000-2002 Ken Westerback
11: *
12: * Redistribution and use in source and binary forms, with or without
13: * modification, are permitted provided that the following conditions
14: * are met:
15: * 1. Redistributions of source code must retain the above copyright
16: * notice, this list of conditions and the following disclaimer,
17: * without modification, immediately at the beginning of the file.
18: * 2. The name of the author may not be used to endorse or promote products
19: * derived from this software without specific prior written permission.
20: *
21: * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
22: * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
23: * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
24: * IN NO EVENT SHALL THE AUTHOR OR HIS RELATIVES BE LIABLE FOR ANY DIRECT,
25: * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
26: * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
27: * SERVICES; LOSS OF MIND, USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
28: * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
29: * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
30: * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
31: * THE POSSIBILITY OF SUCH DAMAGE.
32: *
33: *-------------------------------------------------------------------------
34: */
35:
36: #define IHA_MAX_SG_ENTRIES 33
37: #define IHA_MAX_TARGETS 16
38: #define IHA_MAX_SCB 32
39: #define IHA_MAX_EXTENDED_MSG 4 /* SDTR(3) and WDTR(4) only */
40:
41: /*
42: * Scatter-Gather Element Structure
43: */
44: struct iha_sg_element {
45: u_int32_t SG_Addr; /* Physical address of segment */
46: u_int32_t SG_Len; /* Length of segment */
47: };
48:
49: /*
50: * iha_scb - SCSI Request structure used by the
51: * Tulip (aka inic-940/950). Note that 32
52: * bit pointers and ints are assumed!
53: */
54:
55: struct iha_scb {
56: TAILQ_ENTRY(iha_scb) SCB_ScbList;
57:
58: bus_dmamap_t SCB_DataDma; /* maps xfer buffer */
59: bus_dmamap_t SCB_SGDma; /* maps scatter-gather list */
60:
61: int SCB_Status; /* Current status of the SCB */
62: #define STATUS_QUEUED 0 /* SCB one of Free/Done/Pend */
63: #define STATUS_RENT 1 /* SCB allocated, not queued */
64: #define STATUS_SELECT 2 /* SCB being selected */
65: #define STATUS_BUSY 3 /* SCB I/O is active */
66: u_int8_t SCB_NxtStat; /* Next state function to apply */
67: int SCB_Flags; /* SCB Flags (xs->flags + private)*/
68: #define FLAG_RSENS 0x00010000 /* Request Sense sent */
69: #define FLAG_SG 0x00020000 /* Scatter/Gather used */
70: #define FLAG_DIR (SCSI_DATA_IN | SCSI_DATA_OUT)
71: u_int8_t SCB_Target; /* Target Id */
72: u_int8_t SCB_Lun; /* Lun */
73: u_int32_t SCB_BufChars; /* size of data buf */
74: u_int32_t SCB_BufCharsLeft; /* Chars left to xfer to/from buf */
75: u_int8_t SCB_HaStat; /* Status of Host Adapter */
76: #define HOST_OK 0x00 /* OK - operation a success */
77: #define HOST_TIMED_OUT 0x01 /* Request timed out */
78: #define HOST_SPERR 0x10 /* SCSI parity error */
79: #define HOST_SEL_TOUT 0x11 /* Selection Timeout */
80: #define HOST_DO_DU 0x12 /* Data Over/Underrun */
81: #define HOST_BAD_PHAS 0x14 /* Unexpected SCSI bus phase */
82: #define HOST_SCSI_RST 0x1B /* SCSI bus was reset */
83: #define HOST_DEV_RST 0x1C /* Device was reset */
84: u_int8_t SCB_TaStat; /* SCSI Status Byte */
85: u_int8_t SCB_Ident; /* Identity Message */
86: u_int8_t SCB_TagMsg; /* Tag Message */
87: u_int8_t SCB_TagId; /* Queue Tag */
88:
89: u_int8_t SCB_CDB[12]; /* SCSI command being executed */
90: u_int8_t SCB_CDBLen; /* Length of SCSI command in CDB */
91:
92: struct scsi_xfer *SCB_Xs; /* xs this SCB is executing */
93:
94: struct iha_sg_element SCB_SGList[IHA_MAX_SG_ENTRIES]; /* SG list */
95: u_int16_t SCB_SGCount; /* # segments in list */
96: u_int16_t SCB_SGIdx; /* index to current element */
97:
98: struct scsi_sense_data SCB_ScsiSenseData; /* DMA-able sense buffer */
99: struct tcs *SCB_Tcs; /* tcs for SCB_Target */
100: };
101:
102: /*
103: * Target Device Control Structure
104: */
105: struct tcs {
106: u_int16_t TCS_Flags;
107: #define FLAG_SCSI_RATE 0x0007 /* Index into tul_rate_tbl[] */
108: #define FLAG_EN_DISC 0x0008 /* Enable disconnect */
109: #define FLAG_NO_SYNC 0x0010 /* No sync data transfer */
110: #define FLAG_NO_WIDE 0x0020 /* No wide data transfer */
111: #define FLAG_1GIGA 0x0040 /* 255 hd/63 sec (64/32) */
112: #define FLAG_SPINUP 0x0080 /* Start disk drive */
113: #define FLAG_WIDE_DONE 0x0100 /* WDTR msg has been sent */
114: #define FLAG_SYNC_DONE 0x0200 /* SDTR msg has been sent */
115: #define FLAG_NO_NEG_SYNC (FLAG_NO_SYNC | FLAG_SYNC_DONE)
116: #define FLAG_NO_NEG_WIDE (FLAG_NO_WIDE | FLAG_WIDE_DONE)
117: u_int8_t TCS_JS_Period;
118: #define PERIOD_WIDE_SCSI 0x80 /* Enable Wide SCSI */
119: #define PERIOD_SYXPD 0x70 /* Synch. SCSI Xfer rate */
120: #define PERIOD_SYOFS 0x0f /* Synch. SCSI Offset */
121: u_int8_t TCS_SConfig0;
122: u_int8_t TCS_TagCnt;
123:
124: struct iha_scb *TCS_NonTagScb;
125: };
126:
127: struct iha_softc {
128: struct device sc_dev;
129:
130: bus_space_tag_t sc_iot;
131: bus_space_handle_t sc_ioh;
132:
133: bus_dma_tag_t sc_dmat;
134: bus_dmamap_t sc_dmamap;
135:
136: struct scsi_link sc_link;
137: struct scsi_adapter sc_adapter;
138:
139: void *sc_ih;
140:
141: /*
142: * Initio specific fields
143: */
144: u_int8_t HCS_Flags;
145: #define FLAG_EXPECT_DISC 0x01
146: #define FLAG_EXPECT_SELECT 0x02
147: #define FLAG_EXPECT_RESET 0x10
148: #define FLAG_EXPECT_DONE_DISC 0x20
149: u_int8_t HCS_Semaph;
150: #define SEMAPH_IN_MAIN 0x00 /* Already in tulip_main */
151: u_int8_t HCS_Phase; /* MSG C/D I/O */
152: #define PHASE_DATA_OUT 0x00 /* 0 0 0 */
153: #define PHASE_DATA_IN 0x01 /* 0 0 1 */
154: #define PHASE_CMD_OUT 0x02 /* 0 1 0 */
155: #define PHASE_STATUS_IN 0x03 /* 0 1 1 */
156: #define PHASE_MSG_OUT 0x06 /* 1 1 0 */
157: #define PHASE_MSG_IN 0x07 /* 1 1 1 */
158: u_int8_t HCS_JSInt;
159: u_int8_t HCS_JSStatus0;
160: u_int8_t HCS_JSStatus1;
161: u_int8_t HCS_SConf1;
162: u_int8_t HCS_Msg[IHA_MAX_EXTENDED_MSG]; /* [0] len, [1] Msg Code */
163:
164: struct iha_scb *HCS_Scb; /* SCB array */
165: struct iha_scb *HCS_ActScb; /* SCB using SCSI bus */
166:
167: TAILQ_HEAD(, iha_scb) HCS_FreeScb, HCS_PendScb, HCS_DoneScb;
168:
169: struct tcs HCS_Tcs[IHA_MAX_TARGETS];
170: };
171:
172: /*
173: * EEPROM for one SCSI Channel
174: *
175: */
176: struct iha_nvram_scsi {
177: u_int8_t NVM_SCSI_Id; /* 0x00 Channel Adapter SCSI Id */
178: u_int8_t NVM_SCSI_Cfg; /* 0x01 Channel configuration */
179: #define CFG_SCSI_RESET 0x0001 /* Reset bus at power up */
180: #define CFG_EN_PAR 0x0002 /* SCSI parity enable */
181: #define CFG_ACT_TERM1 0x0004 /* Enable active term 1 */
182: #define CFG_ACT_TERM2 0x0008 /* Enable active term 2 */
183: #define CFG_AUTO_TERM 0x0010 /* Enable auto terminator */
184: #define CFG_EN_PWR 0x0080 /* Enable power mgmt */
185: u_int8_t NVM_SCSI_CfgByte2; /* 0x02 Unused Channel Cfg byte 2*/
186: u_int8_t NVM_SCSI_Targets; /* 0x03 Number of SCSI targets */
187: /* 0x04 Lower bytes of targ flags*/
188: u_int8_t NVM_SCSI_TargetFlags[IHA_MAX_TARGETS];
189: };
190:
191: /*
192: * Tulip (aka ini-940/950) Serial EEPROM Layout
193: *
194: */
195: struct iha_nvram {
196: /* ---------- Header ------------------------------------------------*/
197: u_int16_t NVM_Signature; /* 0x00 NVRAM Signature */
198: #define SIGNATURE 0xC925
199: u_int8_t NVM_Size; /* 0x02 Size of data structure*/
200: u_int8_t NVM_Revision; /* 0x03 Rev. of data structure*/
201:
202: /* ---------- Host Adapter Structure --------------------------------*/
203: u_int8_t NVM_ModelByte0; /* 0x04 Model number (byte 0) */
204: u_int8_t NVM_ModelByte1; /* 0x05 Model number (byte 1) */
205: u_int8_t NVM_ModelInfo; /* 0x06 Model information */
206: u_int8_t NVM_NumOfCh; /* 0x07 Number of SCSI channel*/
207: u_int8_t NVM_BIOSConfig1; /* 0x08 BIOS configuration 1 */
208: #define BIOSCFG_ENABLE 0x01 /* BIOS enable */
209: #define BIOSCFG_8DRIVE 0x02 /* Support > 2 drives */
210: #define BIOSCFG_REMOVABLE 0x04 /* Support removable drv */
211: #define BIOSCFG_INT19 0x08 /* Intercept int 19h */
212: #define BIOSCFG_BIOSSCAN 0x10 /* Dynamic BIOS scan */
213: #define BIOSCFG_LUNSUPPORT 0x40 /* Support LUN */
214: #define BIOSCFG_DEFAULT (BIOSCFG_ENABLE)
215: u_int8_t NVM_BIOSConfig2; /* 0x09 BIOS configuration 2 */
216: u_int8_t NVM_HAConfig1; /* 0x0a Host adapter config 1 */
217: #define HACFG_BOOTIDMASK 0x0F /* Boot ID number */
218: #define HACFG_LUNMASK 0x70 /* Boot LUN number */
219: #define HACFG_CHANMASK 0x80 /* Boot Channel number */
220: u_int8_t NVM_HAConfig2; /* 0x0b Host adapter config 2 */
221: struct iha_nvram_scsi NVM_Scsi[2]; /* 0x0c */
222: u_int8_t NVM_Reserved[10]; /* 0x34 */
223:
224: /* --------- CheckSum -----------------------------------------------*/
225: u_int16_t NVM_CheckSum; /* 0x3E Checksum of NVRam */
226: };
227:
228: /*
229: * Tulip (aka inic-940/950) PCI Configuration Space Initio Specific Registers
230: *
231: * Offsets 0x00 through 0x3f are the standard PCI Configuration Header
232: * registers.
233: *
234: * Offsets 0x40 through 0x4f, 0x51, 0x53, 0x57, 0x5b, 0x5e and 0x5f are
235: * reserved registers.
236: *
237: * Registers 0x50 and 0x52 always read as 0.
238: *
239: * The register offset names and associated bit field names are taken
240: * from the Inic-950 Data Sheet, Version 2.1, March 1997
241: */
242: #define TUL_GCTRL0 0x54 /* R/W Global Control 0 */
243: #define EEPRG 0x04 /* Enable EEPROM Programming */
244: #define TUL_GCTRL1 0x55 /* R/W Global Control 1 */
245: #define ATDEN 0x01 /* Auto Termination Detect Enable */
246: #define TUL_GSTAT 0x56 /* R/W Global Status - connector type */
247: #define TUL_EPAD0 0x58 /* R/W External EEPROM Addr (lo byte) */
248: #define TUL_EPAD1 0x59 /* R/W External EEPROM Addr (hi byte) */
249: #define TUL_PNVPG 0x5A /* R/W Data port to external BIOS */
250: #define TUL_EPDATA 0x5C /* R/W EEPROM Data port */
251: #define TUL_NVRAM 0x5D /* R/W Non-volatile RAM port */
252: #define NVREAD 0x80 /* Read from given NVRAM addr */
253: #define NVWRITE 0x40 /* Write to given NVRAM addr */
254: #define NVENABLE_ERASE 0x30 /* Enable NVRAM Erase/Write */
255: #define NVRCS 0x08 /* Select external NVRAM */
256: #define NVRCK 0x04 /* NVRAM Clock */
257: #define NVRDO 0x02 /* NVRAM Write Data */
258: #define NVRDI 0x01 /* NVRAM Read Data */
259:
260: /*
261: * Tulip (aka inic-940/950) SCSI Registers
262: */
263: #define TUL_STCNT0 0x80 /* R/W 24 bit SCSI Xfer Count */
264: #define TCNT 0x00ffffff /* SCSI Xfer Transfer Count */
265: #define TUL_SFIFOCNT 0x83 /* R/W 5 bit FIFO counter */
266: #define FIFOC 0x1f /* SCSI Offset Fifo Count */
267: #define TUL_SISTAT 0x84 /* R Interrupt Register */
268: #define RSELED 0x80 /* Reselected */
269: #define STIMEO 0x40 /* Selected/Reselected Timeout */
270: #define SBSRV 0x20 /* SCSI Bus Service */
271: #define SRSTD 0x10 /* SCSI Reset Detected */
272: #define DISCD 0x08 /* Disconnected Status */
273: #define SELED 0x04 /* Select Interrupt */
274: #define SCAMSCT 0x02 /* SCAM selected */
275: #define SCMDN 0x01 /* Command Complete */
276: #define TUL_SIEN 0x84 /* W Interrupt enable */
277: #define ALL_INTERRUPTS 0xff
278: #define TUL_STAT0 0x85 /* R Status 0 */
279: #define INTPD 0x80 /* Interrupt pending */
280: #define SQACT 0x40 /* Sequencer active */
281: #define XFCZ 0x20 /* Xfer counter zero */
282: #define SFEMP 0x10 /* FIFO empty */
283: #define SPERR 0x08 /* SCSI parity error */
284: #define PH_MASK 0x07 /* SCSI phase mask */
285: #define TUL_SCTRL0 0x85 /* W Control 0 */
286: #define RSSQC 0x20 /* Reset sequence counter */
287: #define RSFIFO 0x10 /* Flush FIFO */
288: #define CMDAB 0x04 /* Abort command (sequence) */
289: #define RSMOD 0x02 /* Reset SCSI Chip */
290: #define RSCSI 0x01 /* Reset SCSI Bus */
291: #define TUL_STAT1 0x86 /* R Status 1 */
292: #define STRCV 0x80 /* Status received */
293: #define MSGST 0x40 /* Message sent */
294: #define CPDNE 0x20 /* Data phase done */
295: #define DPHDN 0x10 /* Data phase done */
296: #define STSNT 0x08 /* Status sent */
297: #define SXCMP 0x04 /* Xfer completed */
298: #define SLCMP 0x02 /* Selection completed */
299: #define ARBCMP 0x01 /* Arbitration completed */
300: #define TUL_SCTRL1 0x86 /* W Control 1 */
301: #define ENSCAM 0x80 /* Enable SCAM */
302: #define NIDARB 0x40 /* No ID for Arbitration */
303: #define ENLRS 0x20 /* Low Level Reselect */
304: #define PWDN 0x10 /* Power down mode */
305: #define WCPU 0x08 /* Wide CPU */
306: #define EHRSL 0x04 /* Enable HW reselect */
307: #define ESBUSOUT 0x02 /* Enable SCSI data bus out latch */
308: #define ESBUSIN 0x01 /* Enable SCSI data bus in latch */
309: #define TUL_SSTATUS2 0x87 /* R Status 2 */
310: #define SABRT 0x80 /* Command aborted */
311: #define OSCZ 0x40 /* Offset counter zero */
312: #define SFFUL 0x20 /* FIFO full */
313: #define TMCZ 0x10 /* Timeout counter zero */
314: #define BSYGN 0x08 /* Busy release */
315: #define PHMIS 0x04 /* Phase mismatch */
316: #define SBEN 0x02 /* SCSI data bus enable */
317: #define SRST 0x01 /* SCSI bus reset in progress */
318: #define TUL_SCONFIG0 0x87 /* W Configuration */
319: #define PHLAT 0x80 /* Enable phase latch */
320: #define ITMOD 0x40 /* Initiator mode */
321: #define SPCHK 0x20 /* Enable SCSI parity */
322: #define ADMA8 0x10 /* Alternate dma 8-bits mode */
323: #define ADMAW 0x08 /* Alternate dma 16-bits mode */
324: #define EDACK 0x04 /* Enable DACK in wide SCSI xfer */
325: #define ALTPD 0x02 /* Alternate sync period mode */
326: #define DSRST 0x01 /* Disable SCSI Reset signal */
327: #define SCONFIG0DEFAULT (PHLAT | ITMOD | ALTPD | DSRST)
328: #define TUL_SOFSC 0x88 /* R Offset */
329: #define TUL_SYNCM 0x88 /* W Sync. Xfer Period & Offset */
330: #define TUL_SBID 0x89 /* R SCSI BUS ID */
331: #define TUL_SID 0x89 /* W SCSI ID */
332: #define TUL_SALVC 0x8A /* R FIFO Avail Cnt/Identify Msg */
333: #define TUL_STIMO 0x8A /* W Sel/Resel Time Out Register */
334: #define TUL_SDATI 0x8B /* R SCSI Bus contents */
335: #define TUL_SDAT0 0x8B /* W SCSI Data Out */
336: #define TUL_SFIFO 0x8C /* R/W FIFO */
337: #define TUL_SSIGI 0x90 /* R SCSI signal in */
338: #define REQ 0x80 /* REQ signal */
339: #define ACK 0x40 /* ACK signal */
340: #define BSY 0x20 /* BSY signal */
341: #define SEL 0x10 /* SEL signal */
342: #define ATN 0x08 /* ATN signal */
343: #define MSG 0x04 /* MSG signal */
344: #define CD 0x02 /* C/D signal */
345: #define IO 0x01 /* I/O signal */
346: #define TUL_SSIGO 0x90 /* W SCSI signal out */
347: #define TUL_SCMD 0x91 /* R/W SCSI Command */
348: #define NO_OP 0x00 /* Place Holder for tulip_wait() */
349: #define SEL_NOATN 0x01 /* Select w/o ATN Sequence */
350: #define XF_FIFO_OUT 0x03 /* FIFO Xfer Information out */
351: #define MSG_ACCEPT 0x0F /* Message Accept */
352: #define SEL_ATN 0x11 /* Select w ATN Sequence */
353: #define SEL_ATNSTOP 0x12 /* Select w ATN & Stop Sequence */
354: #define SELATNSTOP 0x1E /* Select w ATN & Stop Sequence */
355: #define SEL_ATN3 0x31 /* Select w ATN3 Sequence */
356: #define XF_DMA_OUT 0x43 /* DMA Xfer Information out */
357: #define EN_RESEL 0x80 /* Enable Reselection */
358: #define XF_FIFO_IN 0x83 /* FIFO Xfer Information in */
359: #define CMD_COMP 0x84 /* Command Complete Sequence */
360: #define XF_DMA_IN 0xC3 /* DMA Xfer Information in */
361: #define TUL_STEST0 0x92 /* R/W Test0 */
362: #define TUL_STEST1 0x93 /* R/W Test1 */
363:
364: /*
365: * Tulip (aka inic-940/950) DMA Registers
366: */
367: #define TUL_DXPA 0xC0 /* R/W DMA Xfer Physcl Addr 0-31*/
368: #define TUL_DXPAE 0xC4 /* R/W DMA Xfer Physcl Addr 32-63*/
369: #define TUL_DCXA 0xC8 /* R DMA Curr Xfer Physcl Addr 0-31*/
370: #define TUL_DCXAE 0xCC /* R DMA Curr Xfer Physcl Addr 32-63*/
371: #define TUL_DXC 0xD0 /* R/W DMA Xfer Counter */
372: #define TUL_DCXC 0xD4 /* R DMA Current Xfer Counter */
373: #define TUL_DCMD 0xD8 /* R/W DMA Command Register */
374: #define SGXFR 0x80 /* Scatter/Gather Xfer */
375: #define RSVD 0x40 /* Reserved - always reads as 0 */
376: #define XDIR 0x20 /* Xfer Direction 0/1 = out/in */
377: #define BMTST 0x10 /* Bus Master Test */
378: #define CLFIFO 0x08 /* Clear FIFO */
379: #define ABTXFR 0x04 /* Abort Xfer */
380: #define FRXFR 0x02 /* Force Xfer */
381: #define STRXFR 0x01 /* Start Xfer */
382: #define ST_X_IN (XDIR | STRXFR)
383: #define ST_X_OUT ( STRXFR)
384: #define ST_SG_IN (SGXFR | ST_X_IN)
385: #define ST_SG_OUT (SGXFR | ST_X_OUT)
386: #define TUL_ISTUS0 0xDC /* R/W Interrupt Status Register */
387: #define DGINT 0x80 /* DMA Global Interrupt */
388: #define RSVRD0 0x40 /* Reserved */
389: #define RSVRD1 0x20 /* Reserved */
390: #define SCMP 0x10 /* SCSI Complete */
391: #define PXERR 0x08 /* PCI Xfer Error */
392: #define DABT 0x04 /* DMA Xfer Aborted */
393: #define FXCMP 0x02 /* Forced Xfer Complete */
394: #define XCMP 0x01 /* Bus Master Xfer Complete */
395: #define TUL_ISTUS1 0xDD /* R DMA status Register */
396: #define SCBSY 0x08 /* SCSI Busy */
397: #define FFULL 0x04 /* FIFO Full */
398: #define FEMPT 0x02 /* FIFO Empty */
399: #define XPEND 0x01 /* Xfer pending */
400: #define TUL_IMSK 0xE0 /* R/W Interrupt Mask Register */
401: #define MSCMP 0x10 /* Mask SCSI Complete */
402: #define MPXFER 0x08 /* Mask PCI Xfer Error */
403: #define MDABT 0x04 /* Mask Bus Master Abort */
404: #define MFCMP 0x02 /* Mask Force Xfer Complete */
405: #define MXCMP 0x01 /* Mask Bus Master Xfer Complete */
406: #define MASK_ALL (MXCMP | MFCMP | MDABT | MPXFER | MSCMP)
407: #define TUL_DCTRL0 0xE4 /* R/W DMA Control Register */
408: #define SXSTP 0x80 /* SCSI Xfer Stop */
409: #define RPMOD 0x40 /* Reset PCI Module */
410: #define RSVRD2 0x20 /* SCSI Xfer Stop */
411: #define PWDWN 0x10 /* Power Down */
412: #define ENTM 0x08 /* Enable SCSI Terminator Low */
413: #define ENTMW 0x04 /* Enable SCSI Terminator High */
414: #define DISAFC 0x02 /* Disable Auto Clear */
415: #define LEDCTL 0x01 /* LED Control */
416: #define TUL_DCTRL1 0xE5 /* R/W DMA Control Register 1 */
417: #define SDWS 0x01 /* SCSI DMA Wait State */
418: #define TUL_DFIFO 0xE8 /* R/W DMA FIFO */
419:
420: #define TUL_WCTRL 0xF7 /* ?/? Bus master wait state control */
421: #define TUL_DCTRL 0xFB /* ?/? DMA delay control */
422:
423: /* Functions used by higher SCSI layers, the kernel, or iha.c and iha_pci.c */
424:
425: int iha_scsi_cmd(struct scsi_xfer *);
426: int iha_intr(void *);
427: void iha_minphys(struct buf *);
428: int iha_init_tulip(struct iha_softc *);
429:
430:
CVSweb
![[BACK]](/icons/back.gif){kind=icon}
Return to iha.h CVS log ![[TXT]](/icons/text.gif){kind=icon}
![[DIR]](/icons/dir.gif){kind=icon}
Up to [local] / sys / dev / ic