/* $OpenBSD: eeprom.h,v 1.11 2007/04/10 17:47:54 miod Exp $ */
/*
* Copyright (c) 1995 Theo de Raadt
* All rights reserved.
* Portions Copyright (c) 1997, Jason Downs. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
/*
* This structure defines the contents of the EEPROM for all Sun
* Workstations with the SunMon monitor.
*
* The EEPROM is divided into a diagnostic section, a reserved section,
* a ROM section, and a software section (defined in detail elsewhere).
*/
/*
* Note that most places where the PROM stores a "true/false" flag,
* the true value is 0x12 and false is the usual zero. Such flags
* all take the values EE_TRUE or EE_FALSE so this file does not
* need to define so many value macros.
*/
#define EE_TRUE 0x12
#define EE_FALSE 0x00
struct ee_keymap {
u_char keymap[128]; /* PROM/EEPROM are 7 bit */
};
#define PW_SIZE 8 /* max size of a password entry */
struct password_inf {
u_short bad_counter; /* illegal password count */
char pw_mode; /* mode */
char pw_bytes[PW_SIZE]; /* password */
};
#define NON_SECURE_MODE 0x00 /* non-secure */
#define COMMAND_SECURE_MODE 0x01 /* command secure */
#define FULLY_SECURE_MODE 0x5e /* fully secure */
/* 0, 2-0x5d, 0x5f-0xff: non secure*/
#define MAX_SLOTS 12
#define CONFIG_SIZE 16 /* bytes of config data for each slot */
struct eeprom {
struct ee_diag {
u_int eed_test; /* 0x000: diagnostic test write area */
u_short eed_wrcnt[3]; /* 0x004: diag area write count (3 copies) */
short eed_nu1;
u_char eed_chksum[3]; /* 0x00c: diag area checksum (3 copies) */
char eed_nu2;
time_t eed_hwupdate; /* 0x010: date of last hardware update */
char eed_memsize; /* 0x014: MB's of memory in system */
char eed_memtest; /* 0x015: MB's of memory to test */
char eed_scrsize; /* 0x016: screen size */
#define EED_SCR_1152X900 0x00
#define EED_SCR_1024X1024 0x12
#define EED_SCR_1600X1280 0x13
#define EED_SCR_1440X1440 0x14
#define EED_SCR_640X480 0x15
#define EED_SCR_1280X1024 0x16
char eed_dogaction; /* 0x017: watchdog reset action */
#define EED_DOG_MONITOR 0x00 /* return to monitor command level */
#define EED_DOG_REBOOT 0x12 /* perform power on reset and reboot */
char eed_defboot; /* 0x018: default boot? */
#define EED_DEFBOOT 0x00 /* do default boot */
#define EED_NODEFBOOT 0x12 /* don't do default boot */
char eed_bootdev[2]; /* 0x019: boot device name (e.g. xy, ie) */
u_char eed_bootctrl; /* 0x01b: controller number */
u_char eed_bootunit; /* 0x01c: unit number */
u_char eed_bootpart; /* 0x01d: partition number */
char eed_kbdtype; /* 0x01f: non-Sun keyboard type - for OEM's */
#define EED_KBD_SUN 0 /* one of the Sun keyboards */
char eed_console; /* 0x01f: console device */
#define EED_CONS_BW 0x00 /* use b&w monitor */
#define EED_CONS_TTYA 0x10 /* use tty A port */
#define EED_CONS_TTYB 0x11 /* use tty B port */
#define EED_CONS_COLOR 0x12 /* use color monitor */
#define EED_CONS_P4 0x20 /* use the P4 monitor */
char eed_showlogo; /* 0x020: display Sun logo? */
#define EED_LOGO 0x00
#define EED_NOLOGO 0x12
char eed_keyclick; /* 0x021: keyboard click? */
#define EED_NOKEYCLICK 0x00
#define EED_KEYCLICK 0x12
char eed_diagdev[2]; /* 0x022: boot device name (e.g. xy, ie) */
u_char eed_diagctrl; /* 0x024: controller number */
u_char eed_diagunit; /* 0x025: unit number */
u_char eed_diagpart; /* 0x026: partition number */
#define EED_WOB 0x12 /* bring system up white on black */
u_char eed_videobg;
char eed_diagpath[40]; /* 0x028: boot path of diagnostic */
#define EED_TERM_34x80 00
#define EED_TERM_48x120 0x12 /* for large scrn size 1600x1280 */
u_char eed_colsize; /* 0x050: number of columns */
u_char eed_rowsize; /* 0x051: number of rows */
char eed_nu5[6];
struct eed_tty_def { /* 0x058: tty port defaults */
char eet_sel_baud; /* user specifies baud rate */
#define EET_DEFBAUD 0x00
#define EET_SELBAUD 0x12
u_char eet_hi_baud; /* upper byte of baud rate */
u_char eet_lo_baud; /* lower byte of baud rate */
u_char eet_rtsdtr; /* flag for dtr and rts */
#define NO_RTSDTR 0x12
char eet_unused[4];
} eed_ttya_def, eed_ttyb_def;
char eed_banner[80]; /* 0x068: replacement banner */
/* last two chars must be \r\n (XXX - why not \0?) */
u_short eed_pattern; /* 0x0b8: test pattern - must contain 0xAA55 */
short eed_nu6;
struct eed_conf { /* 0x0bc: system configuration, by slot */
union {
struct eec_gen {
u_char eec_type; /* board type code */
char eec_size[CONFIG_SIZE - 1];
} eec_gen;
char conf_byte[CONFIG_SIZE];
u_char eec_type; /* type of this board */
#define EEC_TYPE_NONE 0 /* no board this slot */
#define EEC_TYPE_CPU 0x01 /* cpu */
struct eec_cpu {
u_char eec_type; /* board type */
u_char eec_cpu_memsize; /* MB's on cpu */
int eec_cpu_unused:6;
int eec_cpu_dcp:1; /* dcp? */
int eec_cpu_68881:1; /* 68881? */
u_char eec_cpu_cachesize; /* KB's cache */
} eec_cpu;
struct eec_cpu_alt {
u_char eec_type; /* board type */
u_char memsize; /* MB's on cpu */
u_char option; /* option flags */
#define CPU_HAS_DCP 0x02
#define CPU_HAS_68881 0x01
u_char cachesize; /* KB's in cache */
} eec_cpu_alt;
#define EEC_TYPE_MEM 0x02 /* memory board */
struct eec_mem {
u_char eec_type; /* board type */
u_char eec_mem_size; /* MB's on card */
} eec_mem;
#define EEC_TYPE_COLOR 0x03 /* color frame buffer */
struct eec_color {
u_char eec_type; /* board type */
char eec_color_type;
#define EEC_COLOR_TYPE_CG2 2 /* cg2 color board */
#define EEC_COLOR_TYPE_CG3 3 /* cg3 color board */
#define EEC_COLOR_TYPE_CG5 5 /* cg5 color board */
} eec_color;
#define EEC_TYPE_BW 0x04 /* b&w frame buffer */
#define EEC_TYPE_FPA 0x05 /* floating point accelerator */
#define EEC_TYPE_DISK 0x06 /* SMD disk controller */
struct eec_disk {
u_char eec_type; /* board type */
char eec_disk_type; /* controller type */
#define EEC_DISK_TYPE_X450 1
#define EEC_DISK_TYPE_X451 2
char eec_disk_ctlr; /* controller number */
char eec_disk_disks; /* number of disks */
char eec_disk_cap[4]; /* capacity */
#define EEC_DISK_NONE 0
#define EEC_DISK_130 1
#define EEC_DISK_280 2
#define EEC_DISK_380 3
#define EEC_DISK_575 4
#define EEC_DISK_900 5
} eec_disk;
#define EEC_TYPE_TAPE 0x07 /* 1/2" tape controller */
struct eec_tape {
u_char eec_type; /* board type */
char eec_tape_type; /* controller type */
#define EEC_TAPE_TYPE_XT 1 /* Xylogics 472 */
#define EEC_TAPE_TYPE_MT 2 /* TapeMaster */
char eec_tape_ctlr; /* controller number */
char eec_tape_drives; /* number of drives */
} eec_tape;
#define EEC_TYPE_ETHER 0x08 /* Ethernet controller */
#define EEC_TYPE_TTY 0x09 /* terminal multiplexer */
struct eec_tty {
u_char eec_type; /* board type */
char eec_tty_lines; /* number of lines */
#define MAX_TTY_LINES 16
char manufacturer; /* code for maker */
#define EEC_TTY_UNKNOWN 0
#define EEC_TTY_SYSTECH 1
#define EEC_TTY_SUN 2
} eec_tty;
#define EEC_TYPE_GP 0x0a /* graphics processor/buffer */
struct eec_gp {
u_char eec_type; /* board type */
char eec_gp_type;
#define EEC_GP_TYPE_GPPLUS 1 /* GP+ graphic processor board */
#define EEC_GP_TYPE_GP2 2 /* GP2 graphic processor board */
} eec_gp;
#define EEC_TYPE_DCP 0x0b /* DCP ??? XXX */
#define EEC_TYPE_SCSI 0x0c /* SCSI controller */
struct eec_scsi {
u_char eec_type; /* board type */
char eec_scsi_type; /* host adaptor type */
#define EEC_SCSI_SUN2 2
#define EEC_SCSI_SUN3 3
char eec_scsi_tapes; /* number of tapes */
char eec_scsi_disks; /* number of disks */
char eec_scsi_tape_type;
#define EEC_SCSI_SYSG 1
#define EEC_SCSI_MT02 2
char eec_scsi_disk_type;
#define EEC_SCSI_MD21 1
#define EEC_SCSI_ADAPT 2
char eec_scsi_driv_code[2];
#define EEC_SCSI_D71 1
#define EEC_SCSI_D141 2
#define EEC_SCSI_D327 3
} eec_scsi;
#define EEC_TYPE_IPC 0x0d
#define EEC_TYPE_GB 0x0e
#define EEC_TYPE_SCSI375 0x0f
#define EEC_TYPE_MAPKIT 0x10
struct eec_mapkit {
u_char eec_type; /* board type */
char eec_mapkit_hw; /* whether INI */
#define EEC_TYPE_MAPKIT_INI 1
} eec_mapkit;
#define EEC_TYPE_CHANNEL 0x11
#define EEC_TYPE_ALM2 0x12
struct eec_generic_net {
#define EEC_TYPE_GENERIC_NET 0x13
u_char eec_devtype; /* board type */
u_char eec_mem_type; /* Memory type */
u_char gn_nu1;
u_char gn_nu2;
#define ID_VME 0x0 /* Data buffers are in VME space(Shared) */
#define ID_DVMA 0x1 /* or DVMA buffer memory type */
char *dev_reg_ptr;
} eec_generic_net;
#define EEC_TYPE_END 0xff /* end of card cage */
} eec_un;
} eed_conf[MAX_SLOTS + 1];
#define EEPROM_TABLE 0x58 /* 1 indicates alternate key table. */
u_char which_kbt; /* 0x18C: which keytable? */
/*
* Note. The following contains the full keyboard id
* returned by the type4 transmit layout command. It is not
* necessarily anything to do with locale of operation.
*/
u_char ee_kb_type;
u_char ee_kb_id; /* 0x18E: keyboard id in case of EEPROM table */
#define EEPROM_LOGO 0x12
u_char otherlogo; /* 0x18F: True if eeprom logo needed */
struct ee_keymap ee_keytab_lc[1]; /* 0x190: */
struct ee_keymap ee_keytab_uc[1]; /* 0x210: */
u_char ee_logo[64][8]; /* 0x290: A 64X64 bit space for custom/OEM designed logo icon */
struct password_inf ee_password_inf; /* 0x490: reserved */
char eed_resv[0x500 - 0x49c]; /* 0x49c: reserved */
} ee_diag;
struct ee_resv { /* reserved area of EEPROM */
u_short eev_wrcnt[3]; /* 0x500: write count (3 copies) */
short eev_nu1;
u_char eev_chksum[3]; /* 0x508: reserved area checksum (3 copies) */
char eev_nu2;
char eev_resv[0x600 - 0x50c]; /* 0x50c: */
} ee_resv;
struct ee_rom { /* ROM area of EEPROM */
u_short eer_wrcnt[3]; /* 0x600: write count (3 copies) */
short eer_nu1;
u_char eer_chksum[3]; /* 0x608: ROM area checksum (3 copies) */
char eer_nu2;
char eer_resv[0x700 - 0x60c]; /* 0x60c: */
} ee_rom;
/*
* The following area is reserved for software (i.e. UNIX).
* The actual contents of this area are defined elsewhere.
*/
struct ee_softresv { /* software area of EEPROM */
u_short ees_wrcnt[3]; /* 0x700: write count (3 copies) */
short ees_nu1;
u_char ees_chksum[3]; /* 0x708: software area checksum (3 copies) */
char ees_nu2;
char ees_resv[0x800 - 0x70c]; /* 0x70c: */
} ee_soft;
};
#define EEPROM_BASE 0xffd04000
/*
* The size of the eeprom on machines with the old clock is 2k. However,
* on machines with the new clock (and the `eeprom' in the nvram area)
* there are only 2040 bytes available. (???). Since we really only
* care about the `diagnostic' area, we'll use its size when dealing
* with the eeprom in general.
*/
#define EEPROM_SIZE 0x500
#ifdef _KERNEL
extern char *eeprom_va;
int eeprom_uio(struct uio *);
/*
* Compatibility defines with NetBSD's eeprom.h.
*
* The goal here is to provide enough compatibility for kernel drivers to
* compile without changes; not to make userland utilities compile. Userland
* should use the native interface.
*/
#define EE_CONS_BW EED_CONS_BW
#define EE_CONS_TTYA EED_CONS_TTYA
#define EE_CONS_TTYB EED_CONS_TTYB
#define EE_CONS_COLOR EED_CONS_COLOR
#define EE_CONS_P4OPT EED_CONS_P4
#define EE_SCR_1152X900 EED_SCR_1152X900
#define EE_SCR_1024X1024 EED_SCR_1024X1024
#define EE_SCR_1600X1280 EED_SCR_1600X1280
#define EE_SCR_1440X1440 EED_SCR_1440X1440
#define EE_SCR_640X480 EED_SCR_640X480
#define EE_SCR_1280X1024 EED_SCR_1280X1024
#define eeConsole ee_diag.eed_console
#define eeTtyRows ee_diag.eed_rowsize
#define eeTtyCols ee_diag.eed_colsize
#define eeScreenSize ee_diag.eed_scrsize
#endif /* _KERNEL */
![[BACK]](/icons/back.gif){kind=icon}
Return to eeprom.h CVS log ![[TXT]](/icons/text.gif){kind=icon}
![[DIR]](/icons/dir.gif){kind=icon}
Up to [local] / sys / arch / sparc / include