File: [local] / sys / arch / hp300 / dev / dcareg.h (download)
Revision 1.1.1.1 (vendor branch), Tue Mar 4 16:05:38 2008 UTC (16 years, 5 months ago) by nbrk
Branch: OPENBSD_4_2_BASE, MAIN
CVS Tags: jornada-partial-support-wip, HEAD Changes since 1.1: +0 -0 lines
Import of OpenBSD 4.2 release kernel tree with initial code to support
Jornada 720/728, StrongARM 1110-based handheld PC.
At this point kernel roots on NFS and boots into vfs_mountroot() and traps.
What is supported:
- glass console, Jornada framebuffer (jfb) works in 16bpp direct color mode
(needs some palette tweaks for non black/white/blue colors, i think)
- saic, SA11x0 interrupt controller (needs cleanup)
- sacom, SA11x0 UART (supported only as boot console for now)
- SA11x0 GPIO controller fully supported (but can't handle multiple interrupt
handlers on one gpio pin)
- sassp, SSP port on SA11x0 that attaches spibus
- Jornada microcontroller (jmcu) to control kbd, battery, etc throught
the SPI bus (wskbd attaches on jmcu, but not tested)
- tod functions seem work
- initial code for SA-1111 (chip companion) : this is TODO
Next important steps, i think:
- gpio and intc on sa1111
- pcmcia support for sa11x0 (and sa1111 help logic)
- REAL root on nfs when we have PCMCIA support (we may use any of supported pccard NICs)
- root on wd0! (using already supported PCMCIA-ATA)
|
/* $OpenBSD: dcareg.h,v 1.7 2005/12/28 21:13:40 miod Exp $ */
/* $NetBSD: dcareg.h,v 1.6 1996/02/24 00:55:02 thorpej Exp $ */
/*
* Copyright (c) 1982, 1986, 1990, 1993
* The Regents of the University of California. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. Neither the name of the University nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* @(#)dcareg.h 8.1 (Berkeley) 6/10/93
*/
#include <hp300/dev/iotypes.h> /* XXX */
#ifdef hp700
struct dcadevice {
vu_char dca_reset;
vu_char dca_pad[0x800-1];
vu_char dca_data; /* receive buf or xmit hold */
vu_char dca_ier; /* interrupt enable */
vu_char dca_iir; /* (RO) interrupt identify */
#define dca_fifo dca_iir /* (WO) FIFO control */
vu_char dca_cfcr; /* line control */
vu_char dca_mcr; /* modem control */
vu_char dca_lsr; /* line status */
vu_char dca_msr; /* modem status */
vu_char dca_scr; /* scratch pad */
};
#else
struct dcadevice {
/* card registers */
u_char dca_pad0;
vu_char dca_id; /* 0x01 (read) */
#define dca_reset dca_id /* 0x01 (write) */
u_char dca_pad1;
vu_char dca_ic; /* 0x03 */
u_char dca_pad2;
vu_char dca_ocbrc; /* 0x05 */
u_char dca_pad3;
vu_char dca_lcsm; /* 0x07 */
u_char dca_pad4[8];
/* chip registers */
u_char dca_pad5;
vu_char dca_data; /* 0x11 */
u_char dca_pad6;
vu_char dca_ier; /* 0x13 */
u_char dca_pad7;
vu_char dca_iir; /* 0x15 (read) */
#define dca_fifo dca_iir /* 0x15 (write) */
u_char dca_pad8;
vu_char dca_cfcr; /* 0x17 */
u_char dca_pad9;
vu_char dca_mcr; /* 0x19 */
u_char dca_padA;
vu_char dca_lsr; /* 0x1B */
u_char dca_padB;
vu_char dca_msr; /* 0x1D */
};
#endif
/* interface reset/id (300 only) */
#define DCAID0 0x02
#define DCAID1 0x42
#define DCACON 0x80 /* REMOTE/LOCAL switch */
/* interrupt control (300 only) */
#define DCAIPL(x) ((((x) >> 4) & 3) + 3)
#define IC_IR 0x40
#define IC_IE 0x80
/*
* 16 bit baud rate divisor (lower byte in dca_data, upper in dca_ier)
* NB: This constant is for a 7.3728 clock frequency. The 300 clock
* frequency is 2.4576, giving a constant of 153600.
*/
#ifdef hp300
#define DCABRD(x) (153600 / (x))
#endif
#ifdef hp700
#define DCABRD(x) (460800 / (x))
#endif
/* interrupt enable register */
#define IER_ERXRDY 0x1 /* Enable receiver interrupt */
#define IER_ETXRDY 0x2 /* Enable transmitter empty interrupt */
#define IER_ERLS 0x4 /* Enable line status interrupt */
#define IER_EMSC 0x8 /* Enable modem status interrupt */
/* interrupt identification register */
#define IIR_IMASK 0xf
#define IIR_RXTOUT 0xc
#define IIR_RLS 0x6 /* Line status change */
#define IIR_RXRDY 0x4 /* Receiver ready */
#define IIR_TXRDY 0x2 /* Transmitter ready */
#define IIR_NOPEND 0x1 /* No pending interrupts */
#define IIR_MLSC 0x0 /* Modem status */
#define IIR_FIFO_MASK 0xc0 /* set if FIFOs are enabled */
/* fifo control register */
#define FIFO_ENABLE 0x01 /* Turn the FIFO on */
#define FIFO_RCV_RST 0x02 /* Reset RX FIFO */
#define FIFO_XMT_RST 0x04 /* Reset TX FIFO */
#define FIFO_DMA_MODE 0x08
#define FIFO_TRIGGER_1 0x00 /* Trigger RXRDY intr on 1 character */
#define FIFO_TRIGGER_4 0x40 /* ibid 4 */
#define FIFO_TRIGGER_8 0x80 /* ibid 8 */
#define FIFO_TRIGGER_14 0xc0 /* ibid 14 */
/* character format control register */
#define CFCR_DLAB 0x80
#define CFCR_SBREAK 0x40
#define CFCR_PZERO 0x30
#define CFCR_PONE 0x20
#define CFCR_PEVEN 0x10
#define CFCR_PODD 0x00
#define CFCR_PENAB 0x08
#define CFCR_STOPB 0x04
#define CFCR_8BITS 0x03
#define CFCR_7BITS 0x02
#define CFCR_6BITS 0x01
#define CFCR_5BITS 0x00
/* modem control register */
#define MCR_LOOPBACK 0x10 /* Loop test: echos from TX to RX */
#define MCR_IEN 0x08 /* Out2: enables UART interrupts */
#define MCR_DRS 0x04 /* Out1: resets some internal modems */
#define MCR_RTS 0x02 /* Request To Send */
#define MCR_DTR 0x01 /* Data Terminal Ready */
/* line status register */
#define LSR_RCV_FIFO 0x80
#define LSR_TSRE 0x40 /* Transmitter empty: byte sent */
#define LSR_TXRDY 0x20 /* Transmitter buffer empty */
#define LSR_BI 0x10 /* Break detected */
#define LSR_FE 0x08 /* Framing error: bad stop bit */
#define LSR_PE 0x04 /* Parity error */
#define LSR_OE 0x02 /* Overrun, lost incoming byte */
#define LSR_RXRDY 0x01 /* Byte ready in Receive Buffer */
#define LSR_RCV_MASK 0x1f /* Mask for incoming data or error */
/* modem status register */
#define MSR_DCD 0x80 /* Current Data Carrier Detect */
#define MSR_RI 0x40 /* Current Ring Indicator */
#define MSR_DSR 0x20 /* Current Data Set Ready */
#define MSR_CTS 0x10 /* Current Clear to Send */
#define MSR_DDCD 0x08 /* DCD has changed state */
#define MSR_TERI 0x04 /* RI has toggled low to high */
#define MSR_DDSR 0x02 /* DSR has changed state */
#define MSR_DCTS 0x01 /* CTS has changed state */